The value specified for the cmd parameter must be a valid system command.

Recovery

Re-enter the command that generated this error message, specifying a valid system command. Refer to the command description in Commands User's Guide for assistance.

The user must be logged on to the EAGLE, and the user ID must have the authorization to access the command class for the selected command before the command can be entered at a system terminal.

Recovery

The command can be entered only at a terminal that is authorized for the associated EAGLE command class.

Recovery

Perform one of the following:

• Re-enter the command at a terminal that is authorized for that EAGLE command class.
• Contact the system administrator to discuss EAGLE terminal command access privileges for the original terminal.
• If you have system administration authority, change the privileges for the terminal.
  Enter the chg-secu-trm command.

  Note:

  This command cannot be entered the target terminal.

The keyboard for the terminal was locked using the lock command.

Recovery

Unlock the keyboard. Enter the unlock command. Anyone attempting to use the keyboard will be prompted to enter the password of the currently logged-on user.

The frame for the argument detected an overflow condition in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid format and combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

Use a colon (:) to separate multiple blocks.

Recovery

Re-enter the command that generated this error message, specifying a colon (:) between the input values. Refer to the command description in Commands User's Guide for assistance.

The command contains too many errors to allow continued processing.

Recovery

Re-enter the command that generated this error message, specifying a valid format and combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A keyword must be specified for the command. Keywords identify the principal action to be performed by the system and consist of one to three words. In the following example, dact-slk is the keyword: dact-slk:loc=1101:port=a

Recovery

Re-enter the command that generated this error message, specifying a keyword. Refer to the command description in Commands User's Guide for assistance.

A hyphen (-) must be used to separate multiple values within a parameter block.

Recovery

Re-enter the command that generated this error message, specifying a hyphen (-) between the input values. Refer to the command description in Commands User's Guide for assistance.

The EAGLE does not recognize the command that was entered.

Recovery

All parameters that are required for the command must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The all=yes parameter cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An argument assignment operator (=) is required in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The EAGLE does not recognize the specified parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An identifier is required in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the parameter must be in the range defined by the command.

Recovery

Re-enter the command that generated this error message, specifying a valid value for the parameter. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The parameter is out of range of the allowed minimum and maximum values

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified value is outside the range of the allowed minimum and maximum values or valid characters for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified value is outside the range of the allowed minimum and maximum values and characters for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the command is already running, then the command cannot be re-entered until the first execution is complete.

Recovery

Re-enter the copy-meas command that generated this error message after the first execution of the command is complete.

A valid syntax must be assigned to the source table parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid syntax must be assigned to the destination table parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid syntax must be assigned to the Operations, Administration and Maintenance (OAM) parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A system error occurred during the execution of a command.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the act-lbp command, the value specified for the loc parameter must indicate an HC-MIM, E5-E1T1, or E5-E1T1-B card, provisioned with the LIMT1 card type, running the SS7ANSI or CCS7ITU application.

For the chg-db command, a value of 1113 or 1115 must be specified for the sloc parameter.

For the ent-card command, a type DSM card must be inserted into an odd-numbered card location. The n+1 slot next to the DSM card must be empty, where n is the odd-numbered location (for example, if the DSM is in location 1101, then the 1102 slot must be empty and not provisioned).

For the ent-trace command, values of 1113 - 1118 cannot be specified for the loc parameter.

For the rept-imt-lvl2 command, MUX card locations (xx09 and xx10), E5-TDM card slots 1114 and 1116, and E5-MDAL slots 1117 and 1118 cannot be specified as values for the loc, sloc, and eloc parameters.

For the rept-stat-gedti command, the value specified for the loc parameter must correspond to the location of an IPSM card that is configured as a GEDTI Hub.

For the rept-stat-j1 command, card location 1118 cannot be specified.

For the rept-stat-rtd command, the following card locations cannot be specified: 1114, 1116, 1117, 1118 (E5-TDM, E5-MDAL cards), and all xy09 and xy10 locations where x is the frame and y is the shelf (HMUX or HIPR MUX cards).

For the rtrv-data-rtdb command, the card location slot must be between 1 and 16 and not 9 or 10. The frame location must be 1xxx, 2xxx, 3xxx, 4xxx, 5xxx, or 6xxx. The shelf location must be 11xx, 12xx, 13xx, 21xx, 22xx, 23xx, 31xx, 32xx, 33xx, 41xx, 42xx, 43xx, 51xx, 52xx, 53xx, or 61xx.

For the tst-disk command, the card in the specified location must be an E5-TDM or an E5-MCAP card.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An attempt was made to log on with a user ID that is already logged on to the system.

Recovery

The IP address of the value for the specified parameter must contain four octets in the range of 1- 254.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A value of 1 - 223 must be specified for octet 1.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

A value of 1- 254 must be specified for octet 2.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A value of 1 - 254 must be specified for octet 3.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A value of 1 - 254 must be specified for octet 4.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address must contain the first octet.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address must contain the second octet.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address must contain the third octet.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address must contain the fourth octet.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address can contain only four octets.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified IP address must contain valid parameters.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified string that must contain at least the minimum number of required characters.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified string cannot exceed the maximum number of characters allowed for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The specified string pattern must conform to the required alphanumeric content for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The first character of the translation name must be a letter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The referenced string pattern must conform to the required numeric content for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An unanticipated system error has been detected. Make a note of this error and the attendant situation.

Recovery

Contact My Oracle Support. See My Oracle Support (MOS).

The entered command is missing a required parameter value.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

A valid number of digits must be entered for the parameter values. The values represented by <min> and <max> specify the valid minimum and maximum number of digits allowed for the command parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

An unanticipated system error has been detected. Make a note of this error and the attendant situation.

Recovery

Contact My Oracle Support for assistance. See My Oracle Support (MOS).

A hyphen (-) character must be used to separate information units.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The command entered contains unnecessary information.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the lower bound must be less than or equal to the value specified for the upper bound for the parameter range.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid number or range of numbers must be specified for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

An invalid number was specified for a parameter value. The value represented by <parm> varies according to the specific command entered.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid IP address must be specified for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid string must be specified for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid mnemonic must be specified for the parameter value.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid point code must be specified for the parameter value.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid number or variable must be specified for the parameter value.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid information unit must be specified for the translation type.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid card location must be specified for the parameter value.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified value must be within the range of the minimum and maximum values allowed for the parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameterss. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The lower bound value of the range must be less than or equal to ihe upper bound value for the parameter range.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified value must contain the supported characters (number, variable, or a range of numbers).

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The specified value must contain a number or the string none.

Recovery

Re-enter the command that generated the error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An underscore character must be encased in double quotes "_".

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the rept-stat-sip command, the card location specified must be an SIP card.

For the rtrv-gttset command, duplicate values cannot be specified for the setidx parameter.

Recovery

For the ent-sip-npp command, the SIPPHCXT table can have a maximum of 101 Phone Contexts which includes 100 Unique and 1 DFLT

Recovery

For the rept-stat-mps command, the card location specified in the loc parameter must contain a Service Module running either the SCCPHC/SCCP64, SIPHC/SIP64, or DEIRHC/DEIR64 GPLs.

Recovery

A valid IP Address must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified network numbers cannot contain all 0 bits or all 1 bits.

For the ent-dlk command, the first octet of the IP Address cannot be 127. The 127 value represents an IP address for loopback.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The specified Host Portion cannot contain all 0 bits or all 1 bits.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the rept-stat-mps command, a Service Module card running the VSCCP, SIPHC, DEIRHC, or ENUMHC application must be configured before this command can be entered.

Recovery

The card location specified with this command must contain a Service Module running the DEIRHC/DEIR64 GPL.

Recovery

Recovery

Re-enter the chg-ip-lnk command with a valid combination of parameters.

Refer to the command description in Commands User's Guide for assistance. Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The IPv6 Address should be in the correct format. Example:

2003:0db8:0000:130F:0000:0000:087C:140B or 2003:db8:0:130F::87C:140B

should be enclosed in double quotes ("").

Recovery

Re-enter the IPv6 address with the correct syntax.

Refer to the command description in Commands User's Guide for assistance. Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

Recovery

1. Use the rept-stat-alm command to display alarm status.
2. Use the unhb-alm command to restore reporting of alarms as needed.
3. Re-enter the inh-alm command that generated this error message.

Refer to the command descriptions in Commands User's Guide for assistance. Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the OBSR feature is enabled or the FLOBR feature is turned on, then the gttsn parameter cannot be specified.

Recovery

For the enable-ctrl-feat command, the A-Port or IGM feature must be turned on before the LOCREQ Query Response feature can be enabled.

For the ent-srvsel command, the A-Port or IGM feature must be turned on before the serv=mnp parameter can be specified.

Recovery

For the enable-ctrl-feat command, the A-Port, G-Port, or IGM feature must be on before the MNP Circular Route Prevention feature can be enabled.

For the ent/chg-srvsel commands, the A-Port or IGM feature must be turned on, or the A-Port or IGM feature must be enabled and the G-Port feature must be turned on before a value of mnp can be specified for the (n)serv parameter.

Recovery

The GTT feature must be turned on before the A-Port feature can be enabled.

The GTT feature must be turned on before the G-Port feature can be turned on.

Recovery

Recovery

The card in the location specified by the loc parameter cannot already be provisioned in the database.

Recovery

The card location specified by the loc or the rloc parameter must contain a card that is valid for the command and was defined previously in the database for the specified card location.

A card that contains the specified signaling link must be equipped in the specified card location.

For the init-card command, the shelf and card must be equipped.

For the rept-meas command, if the enttype=sctpcard parameter is specified, a card must be installed in the location specified by the loc parameter.

Recovery

The IMT table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The Link table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The Shelf table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the act-upgrade command, if a card with card type DCM is used, then values of ss7ipgw, ipgwi, iplim, and iplimi cannot be specified for the appl parameter.

For the chg-card command, the value specified for the loc parameter must indicate a card with a card type of DCM that is running the IPLIM or IPLIMI application.

For the ent-card command, the values specified for the type and appl parameters must be compatible. Refer to the command description in Commands User's Guide for a list of compatible values.

Recovery

The act-slk command cannot be entered while the tst-slk command is in progress.

Recovery

Re-enter the act-slk command that generated this error message after the signal link test is complete.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The card in the location specified by the loc parameter cannot be deleted from the database until any signaling link or TCP/IP data link assigned to the card is deleted from the database.

Recovery - SS7 links

1. Display the signaling links in the database. Enter the rtrv-slk command.
2. Delete the signaling links assigned to the card as necessary. Refer to the Database Administration - SS7 User's Guide for assistance.
3. Re-enter the dlt-card command that generated this error message.

   Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

Recovery - TCP/IP links

For the ent/chg-card command, the shelf location, specified by the loc parameter, must be provisioned.

For the rept-imt-info command, the shelf locations, specified by the sshelf and eshelf parameters, must be provisioned.

Recovery

The command failed because the system detects that:

• The database is incoherent (the command requires that the database be coherent).

• The levels of source databases, during a duplex backup or repair, are not identical on the active and standby OAM fixed disks.

• The database is corrupt. An audit has detected a mismatched checksum in a subset.

Recovery

A severe system fault has occurred and the command was rejected.

Recovery

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A database inconsistency has been detected.

Recovery

Re-enter the rtrv-rte command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

At least one valid optional parameter must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The clli and apc/apca/apci/apcn/apcn24 parameters must be specified together in the command.

Recovery

Re-enter the chg-ls command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - SS7 User's Guide (SS7 linkset) or the Database Administration - IP7 User's Guide (IP linkset) for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the chg-snmp-host command, the specified IP address is in use for another SNMP host.

Recovery

If the card application is SS7ANSI or CCS7ITU, then a value of 56000 or 64000, respectively, must be specified for the bps parameter. If SE-HSL or ST-HSL-A cards are used, then a value of 1984000 or 1536000, respectively, must be specified for the bps parameter.

Recovery

If the ecm=basic parameter is specified, then the pcrn1 and pcrn2 parameters cannot be specified.

Recovery

The Linkset table is corrupt or cannot be found.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

Recovery

The same value must be specified for the ecm parameter for all links in a linkset.

Recovery

If one or more links in a specified linkset are in service, then the apc/apca/apci/apcn/apcn24 and rcontext parameters cannot be specified.

A linkset that still has signaling links assigned to it cannot be changed.

If links in the linkset are in service, then the linkset type cannot be changed.

Recovery

The linkset type must be valid for the card:

• The linkset adjacent point code (APC) type must be the same as the card application type (ANSI or ITU).
• IPSG-M2PA linksets cannot contain IPGWx and IPSG-M3UA link types during transition. After the linkset is transitioned to IPSG-M2PA, only IPSG-M2PA and IPLIM links can be added to the linkset.
• IPSG-M3UA linksets cannot contain SS7IPGW, IPGWI, and IPGHC link types during transition. After the linkset is transitioned to IPSG-M3UA, only IPSG-M3UA links can be added to the linkset.

Recovery

The L2 timer range must be valid for the type of signaling link being provisioned. Refer to the command description in Commands User's Guide for the valid ranges.

Recovery

For the dlt-slk command, the force=yes parameter must be specified to remove the last signaling link in a linkset that is assigned to a route.

For the ent-rte command, the linkset specified by the lsn parameter contain at least one link or the force= yes parameter must be specified.

Recovery

If the ncdpnpfx or dltpfx parameter is specified, then the cdpnpfx parameter must be specified.

Recovery

Re-enter the chg-inpopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the INP/AINPQ User's Guide for assistance.

Links must be available in the linkset that is specified by the lsn parameter.

Recovery

For the chg-clkopts command, the parameters entered are not compatible with the card where the clock resides.

For the ent-dlk command, if the type=acmenet parameter is specified (see the ent-card command), then the duplex and auto parameters cannot be specified.

For the ent-slk command, a valid combination of parameters must be specified. Refer to the command description in Commands User's Guide for valid combinations of parameters.

For the inh/unhb-alm commands, the card specified by the loc parameter must have an IPS, MCP, EROUTE, VSCCP, IPSG, IPLIM, IPLIMI, SS7IPGW, or IPGWI application.

For the rept-stat-iptps command, the history, link, loc, and tpscost parameters can be specified for only IPSG cards.

Recovery

The value specified for the slc parameter cannot already be used by a link in the linkset.

Recovery

A link cannot already be assigned to the specified port.

Recovery

For the ent-snmp-host command, the SNMP host table contains the maximum number of entries allowed.

Recovery

For the chg-snmp-host command, an error occurred while reading the SNMP Host table.

For the ent-snmp-host command, an error occurred while reading the SNMP Host table.

For the dlt-snmp-host command, an error occurred while reading the SNMP Host table.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

At least one optional parameter must be specified in the command.

Recovery

Re-enter the command that generated this error message, specifying at least one valid optional parameter. Refer to the command description in Commands User's Guide for assistance.

The terminal port must be inhibited before the type, baud, prty, sb, and fc parameters can be changed.

Recovery

The Terminal table is corrupt or cannot be found by the system.

Recovery

Re-enter the chg-trm command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the baud parameter must be within the allowed range. Refer to the description of the chg-trm command in the Commands User's Guide for a list of valid values.

Recovery

Re-enter the chg-trm command that generated this error message, specifying a valid combination of parameters.

A valid value must be specified for the prty parameter. Refer to the chg-trm command description in Commands User's Guide for a list of valid values.

Recovery

Re-enter the chg-trm command that generated this error message, specifying a valid combination of parameters.

If E5-MASP hardware is used, then a value of hw or both cannot be specified for the fc parameter.

Recovery

The type=vt320 and prty=none parameters cannot be specified together in the command.

Recovery

There is a problem with the E5-OAM cards or the extended bus interface (EBI) between them. This problem is preventing the system from determining what state the specified terminal or port is in. The terminal or port attributes cannot be changed until the state of the terminal or port can be determined. This error message follows other error messages or system troubles.

Recovery

A card must be equipped and must be in the appropriate location for the card type. Refer to Commands User's Guide for information about the card requirements for a particular command.

For the chg-ee-card and rept-stat-ee commands, the value specified for the loc parameter does not have Eagle Eyes service capability.

For the chg-gedti-card command, the value specified for the loc parameter must correspond to the location of a card provisioned as an IPSM card.

For the dact-gedti command, the value specified for the loc parameter must refer to an equipped card location.

For the disp-tbl and set-tbl commands, the 1117 location is used by E5-MDAL cards, the 1113 and 1115 locations are used by E5-MCAP cards, and the 1114 and 1116 locations are used by E5-TDM cards.

For the ent-card command, the n+1 slot next to the SM or HC-MIM card must be empty, where n is the odd-numbered location (for example, if the SM card is in location 1101, then the 1102 slot must be empty and not provisioned).

For the rept-stat-card command, the card location specified by the loc parameter must be equipped.

For the rept-stat-sflog command, the shelf and card must be equipped.

For the rept-stat-deir command, the card at the specified location does not support this command.

For the rept-stat-enum command, the shelf and card must be equipped, and the card specified by the loc parameter must have an application of enumhc.

For the rtrv-card command, the specified card location must be equipped in the database.

Recovery

1. Display the cards in the database. Enter the rtrv-card command.
2. Re-enter the command that generated this error message, specifying a valid card location. Refer to Commands User's Guide for more information about the card requirements for each command.

   Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The MAS Configuration table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the bps parameter must be supported for the card application. Refer to the command description in Commands User's Guide for a list of valid values.

Recovery

X-list DPCs cannot be specified.

Recovery

If a DPC is specified, it must be an x-list entry, a cluster DPC, or a member of a provisioned cluster.

Recovery

The type=sccs and prty=none parameters cannot be specified together in the command.

Recovery

Re-enter the chg-trm command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The frame value of the loc parameter must be within the valid range.

Recovery

Re-enter the rept-stat-db command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the chg-snmpopts command, an error occurred while reading the SNMP Options table.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the loc parameter is not valid physically. The first and second digits in the loc parameter do not identify a valid shelf.

The frame and shelf portions of the specified card location (loc) can be 11 through 13, 21 through 23; 31 through 33; 41 through 43; 51 through 53; and 61.

The format of the address specified by the loc parameter is XYZZ , where:

X = frame (1, 2, 3, 4, 5, or 6)

Y = shelf within the frame (1, 2, or 3)

ZZ = slot within the shelf range for control shelf,

X = 1, Y = 1, ZZ = 1-8, 11-12

for disc-imt, ZZ = 1-8, 11-13 and 15

for init-card, ZZ = 1-8, 11-13, and 16

for rept-stat-card, ZZ = 1-8, 11-13, and 17

range for extension shelves (all other shelves) is 1-8, 11-18

Recovery

Re-enter the command that generated this error message, specifying a valid shelf ID. Refer to the description for the ent-card command in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the loc parameter is physically invalid. The slot portion of the specified card location can be 1- 8 and 11- 18. Slots 09 and 10 cannot be specified. The card location is xyss , where x is the frame, y is the shelf, and ss is the slot.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the Installation Guide and to the command description in Commands User's Guide for assistance.

For the chg-ee-card command, the loc parameter value specified is reserved for system operation and cannot be specified for the loc parameter.

For the ent/chg/dlt-e1, ent/chg/dlt-j1, and ent/chg/dlt-t1 commands, card locations 1113 - 1118 (E5-OAM cards) cannot be specified as values for the loc parameter.

For the dbg-ddb command, locations 1113 - 1118 cannot be specified as values for the loc or rloc parameters.

For the rept-stat-db command, for E5-OAM cards, locations 1117 and 1118 cannot be specified as values for the loc parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid card location. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An invalid parameter combination has been specified.

Table 2-1 describes the parameter combinations that generate this error message.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The type=none parameter cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the src=usb or src=server parameter is specified, then the action=getrel parameter must be specified. If the src=fixed parameter is specified, then the action=getrel parameter cannot be specified.

Recovery

Re-enter the act-upgrade command, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the act-upgrade command, the Measurements Collection function must be turned off (chg-meas:collect=off) or the Measurements Platform feature must be turned on (chg-measopts:platformenable=on) before a value of convertoam, oamcomplete, or netcomplete can be specified for the action parameter.

For the copy-disk command, OAM measurements collection cannot be in progress when this command is entered.

Recovery - act-upgrade command

1. Determine the status of the Measurements Collection function. Enter the rtrv-meas-sched command.
2. Determine the status of the Measurements Platform feature. Enter the rtrv-measopts command.
3. Turn off the Measurements Collection function or turn on the Measurements Platform feature as necessary. Refer to the Database Administartion - Systems Management User's Guide for assistance.
4. Re-enter the act-upgrade command that generated this error message.

Recovery - copy/format-disk commands

Contact My Oracle Support before entering the copy-disk or format-disk command. See My Oracle Support (MOS).

To format a drive that already contains EAGLE data, the force=yes parameter must be specified.

Recovery

Recovery

1. Ensure that the plug-in flash drive is in the correct location. Refer to Database Administration - System Management User's Guide for assistance.
2. Re-enter the format-disk command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

   Caution:

   Contact My Oracle Support before entering the format-disk command. See My Oracle Support (MOS).

The value specified for the clli parameter cannot be the same as the CLLI that is assigned to the EAGLE.

Recovery

If the media to be formatted contains EAGLE data, then the force=yes parameter must be specified.

Recovery

Contact My Oracle Support before entering the copy-disk command. See My Oracle Support (MOS).

For the disp-disk-dir command, a removable drive must be inserted in the location indicated by the loc or src parameter.

For the tst-disk command, the removable media must be inserted in the corresponding USB port before loc=1113/1115:disk=remove/usb can be specified.

Recovery

If the Cluster Routing and Management Diversity (CRMD) feature is turned on, then a full point code must be entered. Table 2-2 describes the recovery procedures by command.

For the chg-ppsopts command, the values specified for the pc/pca/pci/pcn parameter cannot be the same as the EAGLE capability point code.

For the ent/chg-ls command, the alias point codes cannot be the same as the EAGLE capability point code.

For the ent-rte command, the value specified for the dpc/dpca/dpci/dpcn/dpcn24 parameter cannot be the same as the EAGLE capability point code.

For the ent/dlt/rtrv-pct command, the values specified for the epc/epca/epci/epcn, filtpc/filtpca/filtpci/filtpcn, and realpc/realpca/realpci/realpcn parameters cannot be same as the EAGLE capability point code.

Recovery

For the chg-ppsopts command, the value specified for the pc/pca/pci/pcn parameter cannot be the same as the point code of the system.

For the ent/chg-ls command, the value specified for the apc/apca/apci/apcn/apcn24 parameter cannot match the point code of the system.

For the ent-dstn and ent-rte commands, the value specified for the dpc/dpca/dpci/dpcn/dpcn24 parameter cannot match the point code of the system.

For the ent/dlt/rtrv-pct command, the values specified for the epc/epca/epci/epcn, filtpc/filtpca/filtpci/filtpcn, and realpc/realpca/realpci/realpcn parameters cannot be same as the STP point code.

Recovery

The specified point code is outside of the valid range of values for the command parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid point code value. Refer to the command description in Commands User's Guide for assistance.

For the chg-snmp-host command, the specific IP address or hostname were not found in the SNMP Host table.

For the dlt-snmp-host command, the specific IP address or hostname were not found in the SNMP Host table.

Recovery

The Level 2 Timer Set table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the act-upgrade command, the value specified for the action parameter must correspond to the upgrade phase of the system.

For the act-flash command, the card must be running an inactive GPL.

For the init-flash command the card cannot be running an inactive flash GPL.

Recovery - act-upgrade

1. Display the phase of the upgrade process. Enter the act-upgrade:action=dbstatus command.

   The phase of the upgrade process is shown in the header of the command output.

2. Re-enter the act-upgrade command that generated this error message, specifying an action that corresponds to the upgrade phase. Refer to the command description in Commands User's Guide for a list of upgrade phases.

Recovery - act-flash

1. Display the GPLs running on the cards installed in the system. Enter the rept-stat-gpl command.

   A plus sign (+) in the column between the RUNNING and APPROVED columns indicates an inactive GPL.

2. If the GPL is inactive, re-enter the act-flash command that generated this error message.

   Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

Recovery - init-flash

The Level 3 Timer Set table is corrupt or cannot be found by the system.

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The t20 and it22 parameters cannot be specified together in the command.

Recovery

Re-enter the chg-l3t command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The t21 and it23 parameters cannot be specified together in the command.

Recovery

Re-enter the chg-13t command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

For the chg-snmp-host command, the heartbeat interval is not in range.

For the ent-snmp-host command, the heartbeat interval is not in range.

Recovery

Re-enter the command that generated this error message, specifying a valid heartbeat interval. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the dest parameter is specified, then the action=backup parameter must be specified.

Recovery

Re-enter the chg-db command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

If the src parameter is specified, then the action=restore parameter must be specified.

Recovery

Re-enter the chg-db command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

Recovery

Enter the act-upgrade:action=dbstatus command to verify the version of the database on the active TDM. The version of the database is shown in the VERSION STATUS field.

Contact My Oracle Support for additional assistance. See My Oracle Support (MOS).

Recovery

Enter the act-upgrade:action=dbstatus command to verify the version of the database on the standby TDM. The version of the database is shown in the VERSION STATUS field.

Contact My Oracle Support for additional assistance. See My Oracle Support (MOS).

The specified ANSI point code (pca) cannot match the ANSI capability point code (cpca).

Recovery

Only one of the ncpc, ncpca, ncpci, ncpcn, or ncpcn24 parameters can be specified in the command.

Recovery

Re-enter the command that generated this error message specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

The value specified for the new STP capability point code (cpca, cpci, cpcn, cpcn24) cannot be the same as an existing STP capability point code.

Recovery

For the chg-sid command, the specified site CLLI code cannot be the same as an existing route destination CLLI code.

For the chg-dstn command, if the corresponding destination for the specified destination point code (DPC) is an adjacent signaling point (matched a Far End point code in its linkset entity set), the CLLI of the DPC cannot be assigned to any other destination address.

For the ent-dstn command, the value specified for the clli parameter cannot already exist in the Route table.

Recovery

The new STP capability point code cannot be the same as the STP destination point code.

Recovery

The value specified for the cpc parameter cannot be already assigned as a route destination point code (DPC).

Recovery

The value specified for the pci parameter cannot be the same as the value specified for the cpci parameter.

Recovery

The value specified for the pcn parameter cannot be the same as the value specified for the cpcn parameter.

Recovery

The value specified for the STP destination point code cannot be the same as an existing route DPC or CPC and cannot be the same type as an existing STP point code.

Recovery

If the existing spare ITU-I or spare ITU-N point code is an STP destination point code, then the npci=none or npcn=none parameter (respectively) cannot be specified.

Recovery

The Signaling Link Test Message (SLTM) table is corrupt or cannot be found.

Recovery

Re-enter the chg-slt command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the pattern parameter can contain only the characters 0 – 9, a – f, and A – F. The first two characters of the value cannot be numeric.

Recovery

Re-enter the chg-slt command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The value specified for the pattern parameter must contain an even number of characters.

Recovery

Re-enter the chg-slt command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The sltset and enabled parameters cannot be specified together in the command.

Recovery

Re-enter the rtrv-slt command that generated this error message, specifying a valid combination of parameter. Refer to the command description in Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The value specified for the ncdpnpfx parameter cannot already exist in the INPOPTS table.

Recovery

The User Identification table is corrupt or cannot be found by the system.

Recovery

1. Re-enter the command that generated this error message.
2. Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the nuid parameter or uid parameter cannot already exist in the database.

Recovery

The database can contain a maximum of 100 user IDs.

Recovery

The value specified for the uid parameter must already exist in the database.

Recovery

The command cannot be executed while a database maintenance operation is in progress.

Recovery

Wait for the database maintenance operation to finish, then re-enter the command.

The command was entered with the value 1100 for the loc parameter. Shelf 1100 is the control shelf and cannot be deleted from the database.

Recovery

The shelf specified by the loc parameter cannot already exist in the database.

Recovery

Before a shelf can be removed from the database:

• All affected SS7 signaling links and TCP/IP data links must be deactivated.

• All signaling links and their routes assigned to cards in the affected shelf must be removed from the database.

• All cards in the affected shelf must be removed from the database.

Recovery

An attempt was made to update a database immediately following a dual OAM boot, a switchover, or a database repair, and before the detection of an active standby. An active OAM waits for up to five minutes for an available standby before allowing database updates.

Recovery

A valid value must be specified for the da parameter.

Recovery

Re-enter the send-msg command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid value must be specified for the oa parameter.

Recovery

Re-enter the send-msg command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The destination location specified by the loc parameter must be equipped to receive messages.

Recovery

If any GPL ID other than oamhc is specified, then the all Subsystem ID must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The da and dr parameters cannot be specified together in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The byte, word, or dword parameter must be specified.

Recovery

Re-enter the set-mem command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

A maximum of 40 Called Party Number Prefix values is allowed.

Recovery

The card that is specified cannot be used with this command.

Recovery

The bc parameter must be specified.

Recovery

Re-enter the disp-mem or ent-bp command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The card, loc, or imt parameter must be specified. Only one of these parameters can be specified in the command.

Recovery

Re-enter the ent/disp/dlt-bp or set/disp-mem command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The dr or da parameter must be specified

Recovery

Re-enter the ent-bp command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The cdpnpfx=none parameter cannot be specified.

Recovery

Re-enter the chg-inpopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the INP/AINPQ User's Guide for assistance.

The card, loc, and imt parameters cannot be specified together in the command.

Recovery

Re-enter the ent/disp/dlt-bp or set/disp-mem command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The byte, word, and dword parameters cannot be specified together in the command.

Recovery

Re-enter the set-mem command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The value specified for the bc parameter must be less than or equal to 96.

Recovery

Re-enter the ent-bp command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The dltpfx and ncdpnpfx=none parameters cannot be specified together in the command.

Recovery

Re-enter the chg-inpopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the INP/AINPQ User's Guide for assistance.

The command cannot be entered while another command is already in progress.

Recovery

Re-enter the command after the file transfer is complete.

The value specified for the cdpnpfx parameter must already exist in the INPOPTS table.

Recovery

A valid hard drive must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The src and dest parameters can be specified only once in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The src and dest parameters must be specified together in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

If the chg-inpopts command is entered to delete a Called Party Number Nature of Address value from the INPOPTS table (for example, the cdpnnai=1 and ssnai=none parameters are specified), then the value for the cdpnnai parameter must already exist in the INPOPTS table.

Recovery

A maximum of 5 Called Party Number Nature of Address values is allowed.

Recovery

The source log and destination file combination is not allowed.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

If the stbl parameter is specified, then the dfile parameter must be specified.

Recovery

Re-enter the copy-fta command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the dtbl parameter is specified, then the sfile parameter must be specified.

Recovery

Re-enter the copy-fta command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the dtbl parameter is specified, then the sfile parameter must be specified.

Recovery

Re-enter the copy-fta command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the dfile parameter is specified, then the stbl parameter must be specified.

Recovery

Re-enter the copy-fta command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the all=yes parameter is specified, then the filename parameter cannot be specified.

Recovery

If the filename parameter is not specified, then the all=yes parameter must be specified.

Recovery

Re-enter the dlt-fta command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the initclk parameter is specified with the loc or appl parameter, then:

• A value of 1113 or 1115 must be specified for the loc parameter

  OR

• A value of oam or eoam just be specified for the appl parameter.

Recovery

Re-enter the init-card command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

For the chg-gpl command, the appl and ver parameters must be specified together. If a value of emap or oap is specified for the appl parameter, then the ver parameter does not have to be specified.

For the rtrv-stp command, if the ver parameter is specified, then the appl parameter must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The value specified for the loc parameter must specify an E5-TDM card.

Recovery

The value specified for the gpl parameter must be supported.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command definition in the Commands User's Guide for assistance.

The aud-data command cannot be entered while a previously entered aud-data command is running.

Recovery

Re-enter the aud-data command after the previously entered aud-data command finishes running.

For the copy-fta command, the removable drive has no File Transfer Area and cannot be used as the source or destination.

For the copy-seculog command, the removable drive has no File Transfer Area and cannot be used as the destination.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

The value specified for the loc parameter cannot indicate a fixed disk or removable drive.

Recovery

If the init=yes parameter is specified, then the value of the data parameter must be a Board IDentification (BID) record.

Recovery

Re-enter the chg-bip-rec command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The cdpnnai and snai parameters must be specified together in the command.

Recovery

Re-enter the chg-inopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the INP/AINPQ User's Guide for assistance.

These commands or a configurable command class name are not allowed until the Command Class Management feature has been enabled.

Recovery

For the alw/conn/disc/inh/tst-imt command, an invalid IMT bus was entered. Valid IMT bus entries are A or B.

For the send-msg command, card locations xy09 and xy10 cannot be used with bus B and bus A, respectively.

Recovery

For the alw/conn/disc/inh/tst-imt command, specify a valid IMT bus entry.

For the send-msg command, specify bus=b:loc=xy10 to send a message to the HIPR or HIPR2 MUX card on IMT bus B, and bus=a:loc=xy09 to send a message to the HIPR or HIPR2 MUX card on IMT bus A.

Refer to the command description in Commands User's Guide for assistance. If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

Recovery

Re-enter the command that generated this error message.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the day parameter must be in the range 01–31. The value must accurately reflect the number of days in the month indicated.

Recovery

Re-enter the rtrv-log, rtrv-seculog, or set-date command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

This command stops the echoing of output from a terminal to one or more terminals. Echoing is not set for this terminal.

Recovery

No action required.

When the mtpxlet parameter is specified, the value for minutes (mm) must be in the range 00-59.

Recovery

Re-enter the chg-stpopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The system date month value (yymmdd, where yy is the year, mm is the month, and dd is the day) must be in the range 01 - 12.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Terminal output cannot be echoed to a terminal that is inhibited.

Recovery

For the act-echo command, terminal output cannot be echoed to a terminal that is out of service.

For the inh/rmv-trm command, only terminals that are in service can be placed out of service

Recovery

The nmultcc and multcc parameters must be specified together in the command.

Recovery

Re-enter the chg-gsmopts command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the G-Port User's Guide for assistance.

If a terminal is already echoing to a specified terminal, the act-echo command cannot be entered to echo the terminal's output to that same terminal.

Recovery

No action is necessary since the terminal’s output is already being echoed to the specified terminal.

The E5-TDM cards could not be found.

Recovery

The dlt-user command cannot be entered for the user ID of the user logged on the terminal where the command was issued.

Recovery

The password can contain a maximum of 12 alphanumeric characters.

Recovery

Re-enter the command that generated this error message, specifying a password that is less than or equal to 12 characters. Refer to the command description in Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

The password must contain at least the number of characters specified by the minlin parameter in the chg-secu-dflt command, and no more than 12 alphanumeric characters.

Recovery - login command

Re-enter the command, specifying a larger number of alphanumeric characters. No more than 12 characters can be specified. Refer to the Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

Recovery - chg-pid command

The value entered for the password verification must match the value entered for the password.

Recovery

Re-enter the chg-pid command. When prompted, specify matching values for the password and password verification.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If a user is logged on to the system, then changes cannot be made to that user's ID.

Recovery

The arguments specified by the Configurable Command Class names (parameters CC1 to CC8) must be set to default or provisioned to configurable command class names.

Recovery

If an init-sys command is already processing on another port, then another init-sys command cannot be entered.

Recovery

Re-enter the init-sys command that generated this error message after the system finishes initializing.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

For the chg-snmp-host command, the SNMP feature must be enabled before SNMP host can be changed.

For the ent-snmp-host command, the SNMP feature must be enabled before SNMP host can be entered.

For the dlt-snmp-host command, the SNMP feature must be enabled before SNMP host can be deleted.

For the chg-snmpopts command, the SNMP feature must be enabled before SNMP options changed.

Recovery

For the disp-disk-dir, disp-tbl, init-imt-gpl, set-lba, or set-tbl command, a keyboarding or hardware error may have occurred.

For the disp-disk-dir command, the card must be connected to at least one IMT bus.

Recovery

The card specified by the loc parameter cannot be found in the database or is not allowed by the command. The MUX, E5-TDM, and E5-MDAL cards cannot be initialized by the init-card command.

Recovery

Either the loc or appl parameter, but not both, must be specified in the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

For the alw/rst-card and init-imt-gpl commands, a valid value must be specified or the code parameter or an invalid appl parameter.

For the init-card command, if the serial parameter is specified, then a value of atmansi, ccs7itu, gls, sccp, ss7ansi, ss7gx25, or all must be specified for the appl parameter.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the seconds component in the time, stime, or etime parameter must be in the range 00–59.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the enttype=tt parameter is specified, then the tt parameter must be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The time that the command was entered to specify a measurement report for day-to-hour measurements (type=avldth or type=mtcdth) was between midnight (00:00) and 59 minutes past midnight (00:59). Day-to-hour measurement collection starts at midnight and are updated on an hourly basis. A day-to-hour measurement report cannot be generated before the first hour of measurements have been collected.

Recovery

Wait until after 1:00 AM (01:00) and re-enter the rept-ftp-meas or rept-meas command that generated this error message. Refer to the command description in Commands User's Guide for assistance.

If day-to-hour collection and report processing is in progress, then the type=mtcd and type=mtcdth parameters cannot be specified.

Recovery

Re-enter the rept-ftp-meas or rept-meas command that generated this error message after collection is complete. (The prior period is no longer accessible). Refer to the command description in Commands User's Guide for assistance.

If daily collection and report processing is in progress, then the type=mtcd and type=avid parameters cannot be specified.

Recovery

Re-enter the rept-ftp-meas or rept-meas command that generated this error message after routine collection is complete. Refer to the command description in Commands User's Guide for assistance.

For the chg-ctrl-feat command, if 30 minute measurements collection is in progress, then the 15 Minute Measurements feature cannot be turned on.

For the chg-measopts command, if 30 minute measurements collection is in progress, then the collect15min=on parameter cannot be specified.

For the rept-ftp-meas command, if 30 minute measurements collection is in progress, then a value of comp, systot, avl, or gtwy cannot be specified for the type parameter.

For the rept-meas command, if 30 minute measurements collection is in progress, then a value of systot, comp, or avl cannot be specified for the type parameter.

Recovery - rept-ftp-meas

To get a report before routine collection starts, do one of the following actions:

• Enter the command, specifying the period=last parameter.

  OR

• Enter the command without specifying the period parameter.

Recovery - all commands

Contact My Oracle Support if this error message appears again.

If 5-minute collection and report processing is in progress, then the type=nm parameter cannot be specified.

Recovery

Re-enter the rept-ftp-meas or rept-meas command that generated this error message after the 15-minute measurement collection is complete. (The prior period is no longer accessible). Refer to the command description in Commands User's Guide for assistance.

A valid combination of the period and type parameters must be specified. Refer to the command description in Commands User's Guide for valid parameter combinations.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Measurements Reference for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

An invalid parameter combination has been entered.

Recovery

Re-enter the rept-meas or rept-ftp-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Measurements Reference for assistance.

The component specified is not valid. It has to be one of the AVL, AVLD, COMP, GTWY, MTCD, MTCS, NM, SYSTOT, or RBASE parameters.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

If the period=last parameter is specified, then the hh, qh, and day parameters cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the period=active parameter is specified, then the hh, qh, and day parameters cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the period=all parameter is specified, then the hh, qh, and day parameters cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the period=specific parameter is specified, then the hh or qh parameter must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the enttype=stp or enttype=tt parameter is specified, then the period=active parameter cannot be specified.

Recovery

Re-enter the command that generated this error message specifiying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

If the enttype=link parameter is specified, then the loc and link/port parameters or the lsn parameter must be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Measurements Reference for assistance.

If the type=avl and period=all parameters are specified, then the loc and link/port parameters must be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Measurements Reference for assistance.

If hourly collection and report processing is in progress, then the type=mtch parameter cannot be specified.

Recovery

Re-enter the rept-meas or rept-ftp-meas command that generated thsi error message after collection is complete. (The prior period is no longer accessible).

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the period=specific parameter is specified, then the final two digits of the hh or qh parameter must be 00. Day-to-hour measurement collection starts at midnight and is updated on an hourly basis.

Recovery

Re-enter the rept-ftp-meas command that generated this error message specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Measurements Reference for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The card specified by the loc parameter cannot be found in the database, or is not a LIM card.

The LIMATM, LIME1ATM, LIME1, LIMT1, and DCM card types are the only valid card types for the command. The card must be an E5-ATM, E5-ATM-B, E5-E1T1, E5-E1T1-B, E5-ENET, E5-ENET-B, HC-MIM, or SLIC card.

Recovery

The loc and lsn parameters cannot be specified together in the command.

Recovery

Re-enter the rept-meas or rept-stat-iptps command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

The lsn and link parameters cannot be specified together in the command.

Recovery

Re-enter the rept-meas command that generated this error message specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Measurements Reference for assistance.

If the link parameter is specified, then the loc parameter must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The enttype=tt parameter must be specified before the tt parameter can be specified. If the enttype=tt parameter is specified, then the tt parameter must be specified.

Recovery

Re-enter the command, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The values specified for the loc and enttype parameters must correspond. Refer to the command description in Commands User's Guide for a list of corresponding loc and enttype values.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters.

The enttype=link parameter must be specified before the link parameter can be specified.

Recovery

Re-enter the command that generated this error message specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

If the type=gtwy parameter is specified, and a value of lsdestni, lsonismt, or lsorigni is specified for the enttype parameter for an ITU linkset, then only the lsn parameter can be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the type=systot parameter is specified, or if a value of idpr, origni, origninc, stp, or tt is specified for the enttype parameter, then the lsn parameter cannot be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

If a value of avl, avld, comp, gtwy, mtcd, or systot is specified for the type parameter, then the value specified for the hh parameter must indicate a half-hour boundary (the end of the requested half-hour for the report).

If the type=mtch parameter is specified, then the value specified for the hh parameter must indicate an hourly boundary (half hours ending in 00, such as 0100, etc).

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

For the rept-stat-iptps command, the linkset name specified by the lsn parameter must already exist in the database.

For the dbg-ddb command, the linkset specified by the lsn parameter must already exist in the Linkset table.

Recovery

For the rept-meas command, a valid combination of the type and enttype parameters must be specified.

For the rept-stat-lnp command, the only valid value for the card parameter is sccp-all.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide for assistance.

Only one instance of the command can be running at a time.

Recovery

Re-enter the rept-ftp-meas or rept-meas command that generated this error message after the process that is currently running is complete.

A value of avl, alvd, or avldh must be specified for the type parameter before the nzo=yes parameter can be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Measurements Reference for assistance.

If a value of avld, mtcd, nm, rbase, or mtcs is specified for the type parameter, then the hh and qh parameters cannot be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

If the nc parameter is specified for enttype=origninc reports, then the ni parameter must be specified.

Recovery

Re-enter the rept-meas command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The file being loaded cannot have a name that matches a file that is already in the database.

Recovery

Re-enter the command that generated this error message, specifying the correct file name.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

Recovery

Re-enter the command that generated this error message.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

For the act-upgrade command, the value specified for the release parameter must be at least 11 characters in length and contain a hyphen (-). The format of the value must be xx.xx.xx-yy.yy.yy, where xx.xx.xx is the release number and yy.yy.yy is the engineering build number.

For the chg-db command, the value specified for the file parameter must have the correct extension.

For the chg-tbl command, valid filenames must be in the format filename.extension, with the following requirement:

• File name is 1-8 ASCII characters

For the copy-fta command, file name formats are limited to 8 + 3 DOS-compatible characters.

For the disp-disk-dir command, valid filenames must be in the format filename.extension, with the following requirements:

• File name is 1-8 ASCII characters
• Extension is 0-3 ASCII characters

Wildcards (asterisks) are allowed when the wildcard pattern is enclosed in parentheses:

*

Matches all characters in either filename or extension

?

Matches one character in either filename or extension

file="*.*"

Matches all files on disk

file="*.tbl"

Matches all files on disk with .tbl as the extension

Recovery

Re-enter the command that generated this error message, specifying a valid filename and extension. Refer to the command description in Commands User's Guide for assistance.

If this error message appears again, contact My Oracle Support. See My Oracle Support (MOS).

For the chg-snmp-host command, the target host must be identified either by the IP address or by the hostname, when changing the configuration for an SNMP host.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The argument specified by the class parameter must be a valid configurable or non-configurable command class name.

Recovery

For the aud-data command the table specified by the tblid parameter must already exist.

Recovery

Contact My Oracle Support for assistance. See My Oracle Support (MOS).

A valid value must be specified for the filelength parameter.

Recovery

Contact My Oracle Support before entering the chg-tbl command. See My Oracle Support (MOS).

The value specified for the nclass parameter cannot be the same as an existing class name.

Recovery

For terminals 17 -40, the value of the type parameter must be telnet, emsalm, seas, or none.

The type=emsalm parameter can be specified for terminal numbers from 1 - 16.

Recovery

Re-enter the chg-trm command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

If the value specified for the trm parameter is 17 or above, or if the type=telnet parameter is specified, then the communication settings cannot be specified.

Recovery

Re-enter the chg-trm command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

The value specified for the alias parameter cannot already exist as a destination point code, a site point code, or a capability point code.

Recovery

If a value from 1 - 16 is specified for the trm parmaeter, then the type=telnet parameter cannot be specified.

Recovery

Re-enter the chg-trm command that generated this error message specifying a valid combination of parameters. Refer to the command description in Commands User's Guide and to the Database Administration - System Management User's Guide for assistance.

The specified alias must exist.

Recovery

The alias parameter must be specified with a different point code type than the dpc parameter. A specified alias type cannot already be defined as a destination address.

The aliasa and dpca parameters cannot be specified together in the command. The aliasi and dpci parameters and the aliasn and dpcn parameters cannot be specified together in the command if the prefix subfields are the same (both are spare or both are non-spare).

Recovery

The value specified for the adjacent point code must already be defined in the Destination Point Code table.

Recovery

For the chg-snmp-host command, the value specified for the cmdport / trapport parameter is not within range for the command.

For the ent-snmp-host command, the value specified for the cmdport / trapport parameter is not within range for the command.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the clli parameter must already be defined in the Route table.

Recovery

If a value of telnet, seas, or emsalm, is specified for the type parameter and a Telnet terminal is used (IDs 17-40), then a type IPSM card must be equipped in the system. Parameters for a telnet type terminal cannot be changed unless an IPSM card is used as the target terminal.

Recovery

For the chg-npp-srs command, the TIF Selective Screening feature must be enabled before an AS containing the SELSCR Service Action can be specified as a value for the asn parameter.

For the ent-npp-srs command, the TIF Selective Screening feature must be enabled before an AS containing the SELSCR Service Action can be specified as a value for the asn parameter.

Recovery

The lsn and all=yes parameters cannot be specified together in the command.

Recovery

Re-enter the dlt-rte command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

The value specified for the destination point code parameter cannot already exist as an alias point code.

Recovery

The value specified for the Destination Point Code cannot already exist in the database.

Recovery

The specified destination point code cannot already be defined as an adjacent point code or a secondary adjacent point code.

Recovery

The value specified for the clli parameter must match the value of the clli parameter specified for for the destination.

Recovery

If the gwsa=on, gwsm=on, or gwsd=on parameters are specified, then the scrn parameter must be specified.

Recovery

Re-enter the ent/chg-ls command that generated this error message specifying a valid combination of parameters. Refer to the Database Administration - SS7 User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The gwsd=on parameter can be specified only if the gwsa=on parameter is specified. If the gwsd=on parameter is specified, then the gwsa=on parameter must be specified.

Recovery

Re-enter the ent/chg-ls command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - SS7 User's Guide (for SS7 linksets) or the Database Administration - IP7 User's Guide (for IP linksets) for assistance.

A valid value must be specified for the to the clli parameter.

Recovery

Re-enter the ent/rtrv-dstn command that generated this error message, specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

A valid value must be specified for the point code and clli parameters.

Recovery

Re-enter the ent/rtrv-dstn command that generated this error message specifying a valid combination of parameters. Refer to the command description in the Commands User's Guide and to the Database Administration - SS7 User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

For the chg/rtrv-sid command, a value of none cannot be specified for the cpc, cpca, cpci, cpcn, and cpcn24 parameters.

For the dlt-dstn command, the specified point code must already exist in the database.

For the ent-dstn command, the value specified for the point code parameter must be a valid point code.

The point code 0-0-0 cannot be specified.

The value specified for the new adjacent point code (APC) must have the same point code type as the current APC of the linkset.

Recovery

For the chg-ls command, if the IPSG linkset contains links, then the adapter parameter cannot be specified.

For the dlt-ls command, all links associated with the linkset must be deleted before the linkset can be deleted.

Recovery

The specified adjacent point code (APC) or secondary adjacent point code (SAPC) cannot already be assigned to another linkset.

Recovery

The specified linkset cannot already exist in the database.

Recovery

Recovery

The Linkset table already contains the maximum 1024 linksets.

Recovery

If the linkset is referenced by the historic routeset of any destination, then the linkset cannot be deleted.

Recovery

If the specified destination address is a network address (ni-*-*), or network cluster address (ni-nc-*), the linkset type (see the chg-ls command) used in the route must be b, c, or d.

Recovery

The 6-Way Loadsharing on Routesets feature must be turned on before more than 2 routes can be provisioned with the same relative cost.

Recovery

The linkset specified by the lsn parameter must already exist in the routeset of the destination table entry.

Recovery

For the chg-npp-srs command, the TIF Number Substitution Service Action can not be specified in the AS, if the AS contains the SELSCR Service Action.

For the ent-npp-srs command, the TIF Number Substitution Service Action can not be specified in the AS, if the AS contains the SELSCR Service Action.

Recovery

A routeset can contain a maximum of 6 routes.

Recovery

If any routes are assigned to the destination point code (DPC), then the DPC cannot be deleted.

Recovery

The specified linkset is already in the specified route. A linkset can be entered only once as a route for each destination or for a routeset.

Recovery

The last route cannot be removed if the destination point codes associated are referenced by GTT.

Recovery

The value specifeid for the lsn parameter must already exist in the Linkset table and must be equipped.

Recovery

If the all=yes parameter is specified, then at least one route must be assigned to the routeset.

Recovery

The Route table can contain up to 2000 entries.

Recovery

The value specified for the scrn parameter must already exist in the database.

Recovery

If the AS specified by the asn parameter contains the SELSCR Service Action, then the two numerical values specified by the numerical values list must each be between 0-127 or none.

Recovery

At least one type IPSM card must be equipped before the value specified for the trm parameter can refer to a Telnet or EMSALM terminal.

Recovery

The Telnet (IP User Interface) feature must be enabled and turned on before the type=telnet parameter can be specified.

For the rtrv-trm command, the IP User Interface feature must be enabled before terminal ports 17 through 40 can be specified for the trm parameter.

Recovery

For the inh/unhb-alm commands, if a value of card or dlk is specified for the dev parameter, then the loc parameter must be specified.

For the rept-meas command, if the enttype=sctpcard parameter is specified, then the loc parameter must be specified.

For the rept-stat-card command, if the mode parameter is specified, then the loc parameter must be specified.

For the rept-stat-enum command, if the peakreset parameter is specified, then the loc parameter must be specified.

For the rept-stat-iptps command, if the link parameter is specified, then the loc parameter must be specified.

For the rept-stat-j1 command, if the j1port parameter is specified, then the loc parameter must be specified.

Recovery

Re-enter the command that generated this error message, specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The loc and stat parameters cannot be specified together in the command.

Recovery

Re-enter the rept-stat-card command that generated this error message specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

The command cannot be entered because another process is occuring. Table 2-3 shows the conditions and recovery procedures for the various commands that can generate this error message.

A value of 1, 2, 3, 4, or all cannot be specified for the partition parameter to test a disk which has been formatted but does not contain a DOS directory structure (see the copy-disk command).

Recovery

Re-enter the tst-disk command specifying a valid partition parameter value for the disk being tested.

OR

Re-enter the tst-disk command to test the disk.

Refer to Database Administration - System Management User's Guide for information about formatting and copying a TDM disk.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The trm parameter must be specified.

Recovery

Re-enter the rst-trm command that generated this error message specifying a valid combination of parameters. Refer to the command description in Commands User's Guide for assistance.

For the chg-db command, the force=yes parameter must be specified before the action=canceled parameter can be specified.

For the inh-alm command, the force=yes parameter must be specified to inhibit critical alarms.

For the inh-trm command, the force=yes parameter must be specified to inhibit the last OAP port.

For the init-mux command, if one or more cards are not aligned on the alternate bus, the alternate IMT state will become IS-ANR. If the alternate bus is IS-ANR, then the force=yes parameter must be specified.

For the init-network command, the force=yes parameter must be specified to reset all network cards and override the required four card SS7ANSI or CCS7ITU configuration.

For the rmv-card command, the force=yes parameter must be specified to force the last GLS (if the Integrated GLS feature is not turned on) or the last SCCP card out of service.

For the set-uim-acthresh command the force=yes parameter must be specified to Set the limit=0 parameter for a given interval. Specifying this parameter turns off all occurrences of a specified UIM

Recovery

Contact My Oracle Support for assistance. See My Oracle Support (MOS).

The value specified by the trm parameter must be equipped.

Recovery

The entity or link specified by the loc and link parameters must exist in the database and must be equipped. For commands specifying the dev=slk or dev=dlk parameters, the specified link must exist in the database.

Recovery

At least one Service Module card running the VSCCP application or a GTT-enabled IPSG card must be configured in the system before the command can be entered.

Recovery

The entered command is invalid.

Recovery

Re-enter the command. Refer to the command description in the Commands User's Guide for assistance.

Contact My Oracle Support if this error message appears again. See My Oracle Support (MOS).

The value specified for the loc parameter must be valid for the card type and application. Refer to the command description in Commands User's Guide for valid card types and applications.

Recovery