Use this command to delete breakpoints in the communication or application processors.

Parameters

addr (optional)

The address in the form of segment–offset.

Range:

segment-offset

segment— h’00–h’ffff

offset— h’00–h’ffff

card (optional)

The card location in the form of GPLID–Subsystem ID.

Range:

GPLID-Substystem ID

GPLID— atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility

Subsystem ID— a, b, act, stb, all

The OAMHC GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.

imt (optional)

The IMT address of the card.

Range:

0 - 254

loc (optional)

The card location as stenciled on the shelf of the system.

Range:

1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115

paddr (optional)

The physical offset of the memory address.

Range:

h’00–h’ffffffff

proc (optional)

The processor type.

Range:

appl

Application processor

com

Communication processor

Default:

appl

ueng (optional)

The microengine number.

Note:

This parameter is valid only on IXP-based cards. If this parameter is not specified for IXP-based cards, then the command is assumed to be intended for the ARM processor in the IXP chip.

Range:

0 - 5

Example

dlt-bp:loc=1209:ueng=2

dlt-bp:card=hipr2-all

dlt-bp:loc=6312

Dependencies

The loc, imt, or card parameter must be specified.

Only one of the loc, imt, and card parameters can be specified in the command.

The ueng parameter can be specified only for IXP-based cards.

The card location specified by the loc parameter must be in the database.

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

All of the subsystem values can be specified with the oamhc GPLID. The other GPLID values can be specified only with the all subsystem value.

The addr and paddr parameters cannot be specified together in the command.

Notes

The imt parameter allows this command to be entered for a card that has not been configured in the system.

Output

    Command Accepted - Processing

    tekelecstp 97-01-20 19:21:10 EST Rel 37.0.0
    dlt-bp:card=oam-all:proc=com
    Command entered at terminal #1. 
;