dact-ip-lnk

Use this command to deactivate an IP link and put the link out of service. The state of the link is changed from IS-NR (In-Service-Normal), IS-ANR (In-Service-Abnormal), or OOS-MT (Out-Of-Service-Maintenance), to OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled).

Note:

The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.

Parameters

loc (mandatory)

The card location as stenciled on the shelf of the system.

Range:: 1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115

port (mandatory)

Ethernet interface Port ID.

Range:

a: IP Port A
b: IP Port B
c: IP Port C
d: IP Port D
fca: Fast Copy Port A
fcb: Fast Copy Port B

Example

dact-ip-lnk:loc=1102:port=a

dact-ip-lnk:loc=1203:port=fca

dact-ip-lnk:loc=1103:port=c

dact-ip-lnk:loc=1202:port=d

Dependencies

The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:

E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, or IPSG application
IPSM card
E5-SM4G or E5-SM8G-B card running the VSCCP application
E5-OAM card running the OAMHC application
E5-MCPM-B card
SLIC card

A valid value must be specified for the loc parameter.

The value specified for the port parameter must be supported by the card:

port A-E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card
port A, B- E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
port A, B, FCA, FCB- E5-ENET-B card running the IPGWx or IPSG application
ports A, B, C and D are valid for DEIR/SIP/ENUM applications running on SLIC card

The card at the specified location must be configured.

The card in the specified location must be Active before this command can be executed.

Notes

The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.

Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running DEIR/SIP/ENUM applications.

Output


		  dact-ip-lnk:loc=1101:port=a

    Command Accepted - Processing

    tekelecstp 11-08-16 18:35:44 MST  EAGLE 44.0.0
    dact-ip-lnk:loc=1101:port=a
    Command entered at terminal #1.
;

    tekelecstp 11-08-16 18:35:44 MST  UNKNOWN EAGLE 44.0.0
    Deactivate IP link message sent to card. 
;

    tekelecstp 11-08-16 18:35:44 MST  EAGLE 44.0.0
    Command Completed.
;

dact-ip-lnk:loc=1103:port=c

Command Accepted - Processing

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    dact-ip-lnk:loc=1103:port=c
    Command entered at terminal #18.
;

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    Deactivate IP link message sent to card. 
;

    tekelecstp 16-05-25 03:51:03 MST   EAGLE 46.4.0.0.0-69.1.0
    Command Completed.
;