A UAM Balancing Matrix
The tables in this appendix are in alphabetical order and list Critical, Major, Minor, and Normal alarms that appear for device conditions, and indicate the clearing alarm that appears when each condition is resolved in the system. (Some device conditions are categorized as Normal, and have an associated clearing alarm when the device changes to another Normal condition.)
Note:
A generic clearing alarm, UAM 0500 “Alarm for this entitiy is being cleared,” addresses scenarios where an alarm used to silently remove an active alarm did not make sense for the condition that was being cleared. This UAM is a generic alarm clearing output that applies to all setting alarms (Critical, Major, and Minor).A.1 AIQ System Alarms
Table A-1 shows the AIQ System alarms and the clearing alarm that appears when each condition is resolved.
Table A-1 AIQ System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0592 | AIQ Subsystem is not available | 0595 | AIQ Subsystem is available |
0594 | AIQ Subsystem normal, card(s) abnormal | ||
0593 | AIQ Subsystem is disabled | 0596 | AIQ Subsystem is removed |
0594 | AIQ Subsystem normal, card(s) abnormal | ||
Minor | Normal | ||
0594 | AIQ Subsystem normal, card(s) abnormal | 0595 | AIQ Subsystem is available |
0596 | AIQ Subsystem is removed |
A.2 ATINP System Alarms
Table A-2 shows the critical and minor ATINP System alarms and the clearing alarm that appears when each condition is resolved.
Table A-2 ATINP System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0565 | ATINPQ Subsystem is not available |
0568 0569 |
ATINPQ Subsystem is available ATINPQ Subsystem is removed |
0566 | ATINPQ Subsystem is disabled |
0568 0569 |
ATINPQ Subsystem is available ATINPQ Subsystem is removed |
Major | Normal | ||
0429 | ATINPQ Subsystem degraded, card(s) abnormal |
0568 0569 |
ATINPQ Subsystem is available ATINPQ Subsystem is removed |
Minor | Normal | ||
0567 | ATINPQ Subsystem normal,card(s) abnormal |
0568 0569 |
ATINPQ Subsystem is available ATINPQ Subsystem is removed |
A.3 Card Alarms
Table A-3 shows the critical, major, and minor card alarms and the clearing alarm that appears when each condition is resolved.
Table A-3 Card Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0077 | Card temperature is critical lvl:T2 | 0079 | Card temperature again at nominal levels |
0092 | MDAL not responding | 0093 | MDAL alarm cleared |
0127 | ENUM card capacity exceeded | 0126 | ENUM Threshold Condition cleared |
0442 | RTDB database capacity is 95% full | 0447 | RTDB database capacity alarm cleared |
Major | Normal | ||
0001 | Card has reset | 0014 | Card is present |
0096 | Card has been reloaded | ||
0008 | Active MASP has become isolated | 0009 | MASP became active |
0010 | MASP became standby | ||
0012 | Invalid HW for Integrated Measurements | 0519 | Measurements subsystem available |
0013 | Card is isolated from the system | 0014 | Card is present |
0096 | Card has been reloaded | ||
0031 | HIPR2 detected a major Congested Second | 0032 | HIPR2 Congestion cleared |
0053 | Standby TDM failure | 0054 | Standby TDM failure cleared |
0078 | Card temperature exceeds nominal lvl:T1 | 0079 | Card temperature again at nominal levels |
0088 | Clocks A and B TSCs are out of sync | 0089 | Clocks A and B TSCs are re-synchronized |
0125 | ENUM Threshold -Level 2 exceeded | 0126 | ENUM Threshold Condition cleared |
0132 | Loading failed: table not found | 0096 | Card has been reloaded |
0133 | Loading failed: data read error | ||
0134 | Loading failed: bad checksum returned | ||
0135 | Loading failed: GPL load timeout | ||
0136 | Loading failed: data load timeout | ||
0137 | Loading failed: invalid GPL | ||
0138 | Loading failed: GPL format error | ||
0139 | Loading failed: disk read prep error | ||
0140 | Loading failed: disk read response error | ||
0141 | Loading failed: disk read failed | ||
0300 | TVG Grant Failure | 0301 | TVG Grant Recovery |
0306 | SNM Overload Onset | 0307 | SNM Overload Abated |
0043 | Incorrect feature configuration | 0423 | Card reload attempted |
0047 | Card type not valid for application | ||
0099 | Incompatible HW for provisioned slot | ||
0276 | Insufficient HW for IP7 provisioning | ||
0297 | Incorrect port configuration | ||
0422 | Insufficient extended memory | ||
0441 | Incorrect MDB – CPU | ||
0446 | RTDB database capacity is 80% full | 0447 | RTDB database capacity alarm cleared |
0449 | RTDB re-synchronization in progress | 0445 | RTDB database has been corrected |
0500 | Alarm for this entity is being cleared | ||
0443 | RTDB database is corrupted | 0445 | RTDB database has been corrected |
0451 | RTDB reload is required | ||
0514 | Standby MASP is inhibited | 0515 | Standby MASP is allowed |
0901 | Card DB load timeout, check GLS card | 0902 | Card DB is stable |
0903 | IP Link A is down | 0904 | IP Link A is up |
0905 | IP Link B is down | 0906 | IP Link B is up |
0908 | HW cannot support purchased TPS rate | 0907 | HW limiting TPS rate alarm cleared |
0051 | TSC Sync is in simplex mode | 0052 | TSC sync feature is available |
0466 | STC Network Unavailable | 0467 | STC Network Available |
0088 | Clocks A and B TSCs are out of sync | 0089 | Clocks A and B TSCs are re-synchronized |
0390 | Illegal Address Error | 0388 | Illegal Address Error Cleared |
0391 | Card not responding Error | 0389 | Card responding normally |
0573 | BERT Test Failed | 0574 | BERT Test Passed |
0575 | Card type not HIPR2 | 0500 | Alarm for this entity is being cleared |
0548 | GTT HexTree DB corrupted. TPS derated | 0550 | GTT HexTree DB alarm cleared |
0549 | GTT HexTree DB incoherent. TPS derated | ||
Minor | Normal | ||
UAM | Text | UAM | Text |
0022 | Clock B for card failed, Clock A normal | 0025 | Clock B for card normal |
0023 | Clocks A and B for card failed | 0026 | Clocks A and B for card normal |
0030 | HIPR2 detected a minor Congested Second | 0032 | HIPR2 Congestion cleared |
0034 | Card database is inconsistent | 0033 | Card database has been corrected |
0035 | Card database is corrupted | ||
0037 | Card backup database is inconsistent | 0036 | Card backup database has been corrected |
0038 | Card backup database is corrupted | ||
0044 | Real time clock battery low | 0045 | Real time clock battery restored |
0055 | Persistent device state tbl corrupt | 0057 | Persistent device state tbl corrected |
0056 | Persistent device state tbl diff ver | ||
0102 | Motherboard BIP invalid | 0103 | Motherboard BIP valid |
0124 | ENUM Threshold -Level 1 exceeded | 0126 | ENUM Threshold Condition cleared |
0145 | HS Clock A for card failed, B normal | 0148 | High Speed Clock A for card normal |
0146 | HS Clock B for card failed, A normal | 0149 | High Speed Clock B for card normal |
0147 | High Speed Clocks A and B for card failed | 0159 | High Speed Clocks A and B for card normal |
0298 | Card not using config. SCTP csum method | 0299 | Config. SCTP csum method alarm cleared |
0304 | REPT-NMTSK-DSCD: SNM Discard Onset | 0305 | RECVY-NMTSK-DSCD: SNM Discard Abated |
0444 | RTDB database is inconsistent | 0445 | RTDB database has been corrected |
0448 | RTDB database incoherent | ||
0466 | STC Network Unavailable | 0467 | STC Network Available |
0480 | Timestamp Invalid | 0481 | Timestamp Valid |
0498 | Sanity monitoring is disabled | 0499 | Sanity monitoring is enabled |
0130 | Card successfully loaded with data | ||
0400 | Alarm cleared by deleting card | ||
0294 | REPT-ALMINH: alarm output PERM inhibit | ||
0295 | REPT-ALMINH: alarm output enabled | ||
0296 | REPT-ALMINH: alarm output TEMP inhibit | ||
0570 | Incompatible flash image for sys rel | 0423 | Card reload attempted |
0579 | FC Network Unavailable | 0580 | FC Network Available |
0581 | Loss of heartbeat | 0582 | Heartbeat Available |
0590 | Fast Copy Application De-activated | 0591 | Fast Copy Application Activated |
A.4 CDT (Customer Defined Trouble) Alarms
CDT (Customer Defined Trouble) Alarms shows the critical, major, minor, and normal card alarms and the clearing alarm that appears when each condition is resolved.
Table A-4 CDT (Customer Defined Trouble) Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0058 | Critical customer trouble detected | 0062 | Customer trouble cleared |
Major | Normal | ||
0059 | Major customer trouble detected | 0062 | Customer trouble cleared |
Minor | Normal | ||
0060 | Minor customer trouble detected | 0062 | Customer trouble cleared |
Normal | Normal | ||
0061 | Customer trouble detected | 0062 | Customer trouble cleared |
A.5 Clock (Holdover Clock) Alarms
Clock (Holdover Clock) Alarms shows the critical, major, and minor Holdover Clock alarms and the clearing alarm that appears when each condition is resolved.
Table A-5 Clock (Holdover) Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0063 | Critical holdover clock trbl detected | 0066 | Holdover clock trouble cleared |
Major | Normal | ||
0064 | Major holdover clock trouble detected | 0066 | Holdover clock trouble cleared |
Minor | Normal | ||
0065 | Minor holdover clock trouble detected | 0066 | Holdover clock trouble cleared |
A.6 Clock System Alarms
Table A-6 shows the critical, major, and minor clock alarms and the clearing alarm that appears when each condition is resolved.
Table A-6 Clock System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0128 | All clocks have failed | 0113 | Clock alarm(s) cleared |
Major | Normal | ||
0162 | 1116-P, 1116-S clocks failed | 0113 | Clock alarms cleared |
0164 | 1114-S, 1116-S clocks failed | ||
0166 | 1114-S, 1116-P, 1116-S clocks failed | ||
0169 | 1114-P, 1116-P clocks failed | ||
0170 | 1114-P, 1116-P, 1116-S clocks failed | ||
0171 | 1114-P, 1114-S clocks failed | ||
0172 | 1114-P, 1114-S, 1116-S clocks failed | ||
0173 | 1114-P, 1114-S, 1116-P clocks failed | ||
Minor | Normal | ||
0160 | 1116-S clock failed | 0113 | Clock alarms cleared |
0161 | 1116-P clock failed | ||
0163 | 1114-S clock failed | ||
0165 | 1114-S, 1116-P clocks failed | ||
0167 | 1114-P clock failed | ||
0168 | 1114-P, 1116-S clocks failed |
A.7 DCM Alarms
DCM Alarms shows the major DCM alarm and the clearing alarm that appears when the condition is resolved.
Table A-7 DCM Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0084 | IP Connection Unavailable | 0085 | IP Connection Available |
A.8 DLK Alarms
Table A-8 shows the major and minor DLK alarm and the clearing alarm that appears when the condition is resolved.
Table A-8 DLK Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0537 | Ethernet error threshold exceeded | 0538 | Ethernet error threshold cleared |
0539 | Ethernet Interface Down | 0540 | Ethernet Interface Up |
0588 | FC Port De-activated | 0589 | FC Port Activated |
Minor | Normal | ||
0155 | STP LAN connection unavailable | 0156 | STP LAN connection available |
0536 | IP Connection Excess Re-transmits | 0084 | IP Connection Available |
0085 | IP Connection Available |
A.9 DPC Alarms
DPC Alarms shows the critical, minor, and normal DPC alarms and the clearing alarm that appears when each condition is resolved.
Table A-9 DPC Alarms
UAM | Text | UAM | Text | UAM | Text |
---|---|---|---|---|---|
Critical | Other Alarm Conditions Which Clear Given Alarm | Normal | |||
0313 | DPC is prohibited | 0312 | DPC is restricted | 0311 | DPC is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route | ||
0334 | DPC subsystem is Abnormal | ||||
Minor | Other Alarm Conditions Which Clear Given Alarm | Normal | |||
UAM | Text | UAM | Text | UAM | Text |
0312 | DPC is restricted | 0313 | DPC is prohibited | 0311 | DPC is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route | ||
0334 | DPC subsystem is Abnormal | ||||
Normal | Other Alarm Conditions Which Clear Given Alarm | Normal | |||
0315 | Route is restricted | 0316 | Route is prohibited | 0314 | Route is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route | ||
0316 | Route is prohibited | 0315 | Route is restricted | 0314 | Route is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route |
A.10 DPC System Alarms
DPC System Alarms shows the critical and normal DPC System alarms and the clearing alarm that appears when each condition is resolved.
Table A-10 DPC System Alarms
UAM | Text | UAM | Text | UAM | Text |
---|---|---|---|---|---|
Critical | Other Alarm Conditions Which Clear Given Alarm | Normal | |||
0325 | DPC subsystem is blocked | 0312 | DPC is restricted | 0324 | DPC subsystem is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0327 | DPC subsystem has been deleted | ||
0326 | DPC subsystem is prohibited | 0333 | DPC subsystem is Normal | ||
0332 | DPC subsystem is prohibited and blocked | ||||
0334 | DPC subsystem is Abnormal | ||||
0326 | DPC subsystem is prohibited | 0312 | DPC is restricted | 0324 | DPC subsystem is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0327 | DPC subsystem has been deleted | ||
0325 | DPC subsystem is blocked | 0333 | DPC subsystem is Normal | ||
0332 | DPC subsystem is prohibited and blocked | ||||
0334 | DPC subsystem is Abnormal | ||||
0332 | DPC subsystem is prohibited and blocked | 0312 | DPC is restricted | 0324 | DPC subsystem is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0327 | DPC subsystem has been deleted | ||
0325 | DPC subsystem is blocked | 0333 | DPC subsystem is Normal | ||
0326 | DPC subsystem is prohibited | ||||
0334 | DPC subsystem is Abnormal | ||||
0334 | DPC subsystem is Abnormal | 0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0324 | DPC subsystem is allowed |
0327 | DPC subsystem has been deleted | ||||
0333 | DPC subsystem is Normal | ||||
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0340 | RCVRY-MTPLP-RST: Circ rte status cleared | ||
0320 | REPT-MTPLP-SUST: Sustained circ rt (cong) | 0340 | RCVRY-MTPLP-RST: Circ rte status cleared | ||
0337 | DPC-SS status changed. When DPC subsystem transitions between prohibited and blocked to either blocked or prohibited only, this UAM is raised. |
A.11 DSM Alarms
DSM Alarms shows the major DSM alarm and the clearing alarm that appears when the condition is resolved.
Table A-11 DSM Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0084 | IP Connection Unavailable | 0085 | IP Connection Available |
A.12 E1 Port Alarms
Table A-12 shows the major E1 alarms and the clearing alarm that appears when each condition is resolved.
Table A-12 E1 Port Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0381 | REPT-E1F:FAC-E1 LOS failure | 0386 | RCVRY-E1F:FAC-E1 available |
0382 | REPT-E1F:FAC-E1 LOF failure | ||
0383 | REPT-E1F:FAC-E1 AIS detected | ||
0384 | REPT-E1F:FAC-E1 Far End failure | ||
0385 | REPT-E1F:FAC-E1 10E-3 BER failed | ||
0387 | REPT-E1F:FAC-E1 unavailable |
A.13 EIR Alarms
Table A-13 shows the critical and minor EIR alarms and the clearing alarm that appears when each condition is resolved.
Table A-13 EIR Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0455 | EIR System is not available | 0458 | EIR Subsystem is available |
0459 | EIR Subsystem is removed | ||
0456 | EIR Subsystem is disabled | 0458 | EIR Subsystem is available |
0459 | EIR Subsystem is removed | ||
Major | Normal | ||
0460 | EIR Subsystem degraded, card(s) abnormal | 0458 | EIR Subsystem is available |
0459 | EIR Subsystem is removed | ||
Minor | Normal | ||
0457 | EIR Subsystem normal,card(s) abnormal | 0458 | EIR Subsystem is available |
0459 | EIR Subsystem is removed |
A.14 ENET System Alarms
Table A-14 shows the ENET System alarms and the clearing alarm that appears when each condition is resolved.
Table A-14 ENET System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0537 | Ethernet error threshold exceeded | 0538 | Ethernet error threshold cleared |
0539 | Ethernet Interface Down | 0540 | Ethernet Interface Up |
Minor | Normal | ||
0536 | IP Connection Excess Retranmists | 0085 | IP Connection Available |
A.15 ENUM System Alarms
Table A-15 shows the ENUM System alarms and the clearing alarm that appears when each condition is resolved.
Table A-15 ENUM System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0120 | ENUM SYSTEM is not available | 0121 | ENUM SYSTEM is available |
0123 | ENUM SYSTEM is removed | ||
Major | Normal | ||
0122 | ENUM SYSTEM normal, card(s) abnormal | 0121 | ENUM SYSTEM is available |
0123 | ENUM SYSTEM is removed |
A.16 EROUTE Alarms
Table A-16 shows the critical, major, and minor EROUTE alarms and the clearing alarm that appears when each condition is resolved.
Table A-16 EROUTE Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0468 | All STC Networks Unavailable | 0470 | EROUTE is Removed |
0469 | All STC Cards Unavailable | 0471 | EROUTE System is Available |
Major | Normal | ||
0473 | EROUTE System Capacity Exceeded | 0470 | EROUTE is Removed |
0482 | Card(s) have been denied EROUTE service | 0471 | EROUTE System is Available |
Minor | Normal | ||
0472 | EROUTE System Threshold Exceeded | 0470 | EROUTE is Removed |
0471 | EROUTE System is Available | ||
0474 | EROUTE capacity normal, card(s) abnormal | 0470 | EROUTE is Removed |
0471 | EROUTE System is Available | ||
0475 | NTP Time Unavailable | 0476 | NTP Time Available |
A.17 Ethernet Error Threshold Alarms
Table A-17 shows the major ethernet error threshold alarms and the clearing alarm that appears when each condition is resolved.
Table A-17 Ethernet Error Threshold Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0537 | Ethernet error threshold exceeded | 538 | Ethernet error threshold cleared |
0539 | Ethernet Interface Down | 0540 | Ethernet Interface Up |
A.18 Fast Copy System Alarms
Table A-18 shows the major and minor Fast Copy System alarms and the clearing alarm that appears when the condition is resolved.
Table A-18 Fast Copy System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0576 | All FC Network Unavailable | 0577 | All FC cards removed |
0578 | FC System is Available | ||
Minor | Normal | ||
597 | FC System is Deactivated | 0578 | FC System is Available |
A.19 Frame Alarms
Table A-19 shows the major Frame alarms and the clearing alarms that appear when the condition is resolved.
Table A-19 Frame Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0520 | Frame power usage reached LVL3 | 0523 | Frame power usage normal |
Major | Normal | ||
0521 | Frame power usage reached LVL2 | 0523 | Frame power usage normal |
Minor | Normal | ||
0522 | Frame power usage reached LVL1 | 0523 | Frame power usage normal |
A.20 Fuse Alarms
Table A-20 shows the major fuse alarm and the clearing alarm that appears when the condition is resolved.
Table A-20 Fuse Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0082 | Alarm in fuse panel | 0083 | Fuse panel alarm has cleared |
A.21 GLS Alarms
Table A-21 shows the critical and major GLS alarms and the clearing alarm that appears when each condition is resolved.
Table A-21 GLS Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0292 | GLS is not available | 0290 | GLS is available |
0293 | GLS have been removed from the system | ||
Major | Normal | ||
0291 | GLS is at minimum service limit | 0290 | GLS is available |
0293 | GLS have been removed from the system | ||
0450 | Invalid HW for Integrated GLS | 0290 | GLS is available |
A.22 GPL Alarms
GPL Alarms shows the minor GPL alarms and the clearing alarm that appears when each condition is resolved.
Table A-22 GPL Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0002 | Card is not running approved GPL | 0003 | Alarm cleared for GPL |
0004 | Card is running non-activated GPL | 0005 | Alarm cleared running non-activated GPL |
0040 | GPL is corrupted | 0039 | GPL has been corrected |
A.23 Group Broadcast Alarms
Table A-23 shows the critical and minor Group Broadcast alarms and the clearing alarm that appears when each condition is resolved.
Table A-23 Group Broadcast Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0015 | Group Broadcast Registration Failed | 0017 | Group Broadcast Registration Succeeded |
Minor | Normal | ||
0016 | Single IMT Bus GB Registration | 0017 | Group Broadcast Registration Succeeded |
A.24 GTT Alarms
Table A-24 shows the major GTT alarm and the clearing alarm that appears when the condition is resolved.
Table A-24 GTT System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0630 | Throttle Threshold - exceeded | 0631 | Throttle Threshold - cleared |
A.25 HS Clock System Alarms
Table A-25 shows the critical, major, and minor HS Clock System alarms and the clearing alarm that appears when each condition is resolved.
Table A-25 HS Clock System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0197 | All high speed clocks have failed | 0198 | High Speed clock alarm(s) cleared |
Major | Normal | ||
0185 | 1116-PHS, 1116-SHS clocks failed | 0198 | High Speed clock alarm(s) cleared |
0187 | 1114-SHS, 1116-SHS clocks failed | ||
0189 | 1114-SHS, 1116-PHS,1116-SHS clks failed | ||
0192 | 1114-PHS, 1116-PHS clocks failed | ||
0193 | 1114-PHS, 1116-PHS,1116-SHS clks failed | ||
0194 | 1114-PHS, 1114-SHS clocks failed | ||
0195 | 1114-PHS, 1114-SHS, 1116-SHS clks failed | ||
0196 | 1114-PHS, 1114-SHS, 1116-PHS clks failed | ||
403 | 1114 E1/T1 clock requires TDM-GTI | 409 | Clock configuration corrected |
404 | 1116 E1/T1 clock requires TDM-GTI | ||
405 | 1114, 116 E1/T1 clock requires TDM-GTI | ||
406 | 1114 Clock selection mismatch | ||
407 | 1116 Clock selection mismatch | ||
408 | 1114, 1116 Clock selection mismatch | ||
Minor | Normal | ||
0183 | 1116-SHS clock failed | 0198 | High speed clock alarm(s) cleared |
0184 | 1116-PHS clock failed | ||
0186 | 1114-SHS clock failed | ||
0188 | 1114-SHS, 1116-PHS clocks failed | ||
0190 | 1114-PHS clock failed | ||
0191 | 1114-PHS, 1116-SHS clocks failed |
A.26 IMT Bus Alarms
Table A-26 shows the major, minor, and normal IMT Bus alarms and the clearing alarm that appears when each condition is resolved.
Table A-26 IMT Bus Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0108 | Major IMT failure detected | 0106 | IMT bus alarm cleared |
Minor | Normal | ||
0107 | Minor IMT failure detected | 0106 | IMT bus alarm cleared |
Normal | Normal | ||
0098 | IMT inhibited | 0097 | IMT allowed |
A.27 IMT System Alarms
Table A-27 shows the critical, major, and minor IMT System alarms and the clearing alarm that appears when each condition is resolved.
Table A-27 IMT System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0112 | Major failures detected on both IMTs | 0109 | All IMT system level alarms cleared |
Major | Normal | ||
0028 | IMT Bus util rate exceeds major thresh | 0029 | IMT Bus utilization threshold cleared |
0111 | Failure on both IMT A and IMT B | 0109 | All IMT system level alarms cleared |
0563 | IMT Bit rate mismatch detected | 0564 | IMT Bit rate mismatch cleared |
Minor | Normal | ||
0027 | IMT Bus util rate exceeds minor thresh | 0029 | IMT Bus utilization threshold cleared |
0110 | Failure detected on one IMT bus | 0109 | All IMT system level alarms cleared |
A.28 INP System Alarms
INP System Alarms shows the critical and minor NP System alarms and the clearing alarm that appears when each condition is resolved.
Table A-28 INP System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0395 | INP Subsystem is not available | 0394 | INP Subsystem is available |
0396 | INP Subsystem is disabled | 0397 | INP Subsystem is removed |
Major | Normal | ||
0428 | INP Subsystem degraded, card(s) abnormal | 0394 | INP Subsystem is available |
Minor | Normal | ||
0398 | INP Subsystem normal, card(s) abnormal | 0394 | INP Subsystem is available |
0397 | INP Subsystem is removed |
A.29 IP7CONN Alarms
IP7CONN Alarms shows the major and minor IP Connection alarms and the clearing alarm that appears when each condition is resolved.
Table A-29 IP Connection Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0084 | IP Connection Unavailable | 0085 | IP Connection Available |
0087 | IP Connection manually removed | ||
Minor | Normal | ||
0086 | IP Connection Congested | 0085 | IP Connection Available |
0087 | IP Connection manually removed | ||
0535 | IP Connection Restricted | 0085 | IP Connection Available |
0536 | IP Connection Excess Retransmits | 0085 | IP Connection Available |
A.30 IP7 Alarms
IP7 Alarms shows the major and minor IP Connection alarms and the clearing alarm that appears when each condition is resolved.
Table A-30 IP Connection Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0277 | AS Unavailable | 0278 | AS Available |
Minor | Normal | ||
0279 | AS Restricted | 0280 | AS Unrestricted |
A.31 Linkset Alarms
Table A-31 shows the Linkset alarm and the clearing alarms that appears when the condition is resolved.
Table A-31 Linkset Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0115 | Linkset IP TPS threshold exceeded | 0118 | Linkset IP TPS threshold normal |
0318 | REPT-LKSTO: link set prohibited | 0317 | RCVRY-LKSTO: link set allowed |
0399 | RRCVRY-LKSTO:Alarm clr’d by deleting SLK | ||
0560 | REPT-LKSTO: link set restricted | 0317 | REPT-LKSTO: link set restricted |
A.32 LNP System Alarms
Table A-32 shows the critical and major LNP System alarms and the clearing alarm that appears when each condition is resolved.
Table A-32 LNP System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0424 | LNP Subsystem is not available | 0426 | LNP Subsystem is available |
0435 | LNP Subsystem is disabled | 0434 | LNP Subsystem is removed |
0287 | RTDB Table Level 2 FAK Cap exceeded | 0289 | RTDB Table FAK Capacity Normal |
Major | Normal | ||
0283 | LNP Ported NPAs approaching Feat. Capacity | 0284 | LNP Ported NPAs Capacity Normal |
0285 | LNP Ported LRNs approaching Feat. Capacity | 0286 | LNP Ported LRNs Capacity Normal |
0288 | RTDB Table Level 1 FAK Cap exceeded | 0289 | RTDB Table FAK Capacity Normal |
0427 | LNP Subsystem degraded, card(s) abnormal | 0426 | LNP Subsystem is available |
0436 | LNP ACG node overload | 0426 | LNP Subsystem is available |
Minor | Normal | ||
0425 | LNP Subsystem normal, card(s) abnormal | 0426 | LNP Subsystem is available |
A.33 LSMS Connection Alarms
LSMS Connection Alarms shows the critical and major LSMS Connection alarms and the clearing alarm that appears when each condition is resolved.
Table A-33 LSMS Connection Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0041 | LNP DB Maintenance required. | 0042 | LSMS bulk load complete. |
Major | Normal | ||
0358 | LSMS connection unavailable | 0359 | LSMS connection available |
A.34 LSMS System Alarms
LSMS System Alarms shows the critical and major LSMS System alarms and the clearing alarm that appears when each condition is resolved.
Table A-34 LSMS System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0356 | LSMS unavailable | 0355 | LSMS is available |
0357 | All OAP terminals are removed | ||
0350 | OAP terminals inhibited | 0355 | LSMS is available |
0357 | All OAP terminals are removed | ||
Major | Normal | ||
0341 | OAP unavailable | 0353 | OAP is available |
0354 | One OAP terminal unavailable | 0357 | All OAP terminals are removed |
0362 | LSMS is at min service limit | 0355 | LSMS is available |
0357 | All OAP terminals are removed |
A.35 MCPM Alarms
MCPM Alarms shows the major MCPM alarm and the clearing alarm that appears when the condition is resolved.
Table A-35 MCPM Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0084 | IP Connection Unavailable | 0085 | IP Connection Available |
A.36 MEAS System Alarms
MEAS System Alarms shows the critical, major, and minor MEAS System alarms and the clearing alarm that appears when each condition is resolved.
Table A-36 MEAS System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0518 | Measurements subsystem unavailable | 0519 | Measurements subsystem available |
Major | Normal | ||
0517 | Degraded Mode - multiple cards failed | 0519 | Measurements subsystem available |
Minor | Normal | ||
0516 | Degraded Mode - 1 card failed | 0519 | Measurements subsystem available |
A.37 MPS (ELAP/EPAP) Alarms
Table A-37 shows the critical, major, and minor MPS (ELAP/EPAP) alarms and the clearing alarm that appears when each condition is resolved.
Table A-37 MPS (ELAP/EPAP) Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0370 | Critical Platform Failure(s) | 0250 | MPS available |
0371 | Critical Application Failure(s) | ||
0261 | MPS unavailable | ||
Major | Normal | ||
0372 | Major Platform Failure(s) | 0250 | MPS available |
0373 | Major Application Failure(s) | ||
Minor | Normal | ||
0374 | Minor Platform Failure(s) | 0250 | MPS available |
0375 | Minor Application Failure(s) |
Note:
Critical Platform/Application alarms cause the MPS to go OOS-MT and Major/Minor Platform/Applications alarms cause the MPS to go IS-ANR.
A.38 MPS Alarm Support
The MPS running software release 2.0 (ELAP) or higher. Release 27.0 supports MPS alarms (370-375) and UAMs 442-451 against a card.
Table A-38 MPS Alarm Support
Release 27.0 and higher | |
---|---|
UAM | Format |
0442 0446 0447 |
CARD |
0443-0445 0448-0451 |
CARD |
0370-0375 | MPS1 |
0250 | MPS2 |
A.39 RTX System Alarms
Table A-39 shows the major RTX system alarms and the clearing alarm that appears when the condition is resolved.
Table A-39 RTX System Alarms
UAM | Text | UAM | Text | UAM | Text |
---|---|---|---|---|---|
Critical | Other alarm conditions which clear given alarm | Normal | |||
0534 | RTX is prohibited | 0533 | RTX is restricted | 0532 | RTX is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route | ||
Minor | Other alarm conditions which clear given alarm | Normal | |||
0533 | RTX is restricted | 0534 | RTX is prohibited | 0532 | RTX is allowed |
0319 | REPT-MTPLP-DET: Circ rte det(cong) | 0402 | Alarm cleared by deleting route |
A.40 SCCP Service Alarms
Table A-40 shows the critical, major, and minor SCCP service alarms and the clearing alarm that appears when each condition is resolved.
Table A-40 SCCP Service Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0528 | Service is not available | 0526 | Service is available |
0530 | Service is removed | ||
0529 | Service is disabled | 0526 | Service is available |
0530 | Service is removed | ||
Major | Normal | ||
0547 | Service degraded | 0526 | Service is available |
0530 | Service is removed | ||
Minor | Normal | ||
0527 | Service abnormal | 0526 | Service is available |
0530 | Service is removed |
A.41 SCCP System Alarms
Table A-41 shows the critical, major, and minor SCCP system alarms and the clearing alarm that appears when each condition is resolved.
Table A-41 SCCP System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0331 | SCCP is not available | 0328 | SCCP is available |
0335 | SCCP is removed | ||
0437 | System SCCP TPS Capacity Exceeded | 0329 | System SCCP TPS normal |
0453 | Exceeded Service Error Threshold Lvl 2 | 0454 | Service Error Threshold Alarm Cleared |
Major | Normal | ||
0262 | GTT Duplicate Actn processing stopped | 0263 | GTT Duplicate Actn processing resumed |
0336 | LIM(s) have been denied SCCP service | 0328 | SCCP is available |
0335 | SCCP is removed | ||
0452 | Exceeded Service Error Threshold Lvl 1 | 0454 | Service Error Threshold Alarm Cleared |
Minor | Normal | ||
0330 | System SCCP TPS Threshold exceeded | 0329 | System SCCP TPS normal |
0335 | SCCP is removed | ||
0632 | Alarm Threshold - exceeded | 0631 | Throttle Threshold - cleared |
0633 | Alarm Threshold - cleared |
A.42 SCTP Retransmit Alarms
SCTP Retransmit Alarms shows the critical, major, and minor SCTP retransmit alarms and the clearing alarm that appears when each condition is resolved.
Table A-42 SCTP Retransmit Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Minor | Normal | ||
0536 | IP Connection Excess Retransmits | 0085 | IP Connection Available |
A.43 SEAS OAP Alarms
Table A-43 shows the major and minor SEAS OAP alarms and the clearing alarm that appears when each condition is resolved.
Table A-43 SEAS OAP Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0341 | OAP unavailable | 0353 | OAP is available |
0342 | SEAS UAL unavailable | ||
0354 | One OAP terminal unavailable | ||
0360 | EMS Agent unavailable | 0361 | EMS Agent available |
Minor | Normal | ||
0364 | Configuration data checksum mismatch | 0365 | Configuration data checksum alarm cleared |
0363 | OAP filesystem full | 0361 | EMS Agent available |
A.44 SEAS System Alarms
SEAS System Alarms shows the critical and major SEAS System alarms and the clearing alarm that appears when each condition is resolved.
Table A-44 SEAS System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0349 | SEAS unavailable | 0351 | SEAS is available |
0350 | OAP terminals inhibited | 0352 | SEAS is removed |
Major | Normal | ||
0348 | SEAS is at min service limit | 0351 | SEAS is available |
0352 | SEAS is removed |
A.45 SEAS X25 Alarms
Table A-45 shows the major and minor SEAS X25 alarms and the clearing alarm that appears when each condition is resolved.
Table A-45 SEAS X25 Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0343 | SEAS X.25 Link unavailable | 0347 | SEAS X.25 Link is available |
0345 | All SEAS UAL sessions unavailable | ||
Minor | Normal | ||
0344 | SEAS PVC unavailable | 0347 | SEAS X.25 Link is available |
0346 | SEAS UAL session unavailable |
A.46 Security Log Alarm
Security Log Alarm shows the minor and normal Security Log alarms and the clearing alarm that appears when each condition is resolved.
Table A-46 Security Log Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Minor | Normal | ||
0174 | %full threshold reached-upload required | 0177 | Security log exception cleared |
0175 | LOGGUFROVFL-SECUL–G - upload required | ||
0176 | Stby security log – upload required | ||
Normal | Normal | ||
0178 | Security log failed | 0177 | Security log exception cleared |
A.47 Security System Alarms
Table A-47 shows the major Security System alarm and the clearing alarm that appears when the condition is resolved.
Table A-47 Security System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0392 | OA&M IP Security feature status is OFF | 0393 | OA&M IP Security feature status is ON |
0199 | OA&M IP Security feature disabled | ||
Minor | Normal | ||
0157 | OA&M Security Feature Risk detected | 0158 | OA&M Security Feature Risk cleared |
A.48 SFAPP System Alarms
SFAPP System Alarms shows the critical, major, and minor SFAPP system alarm and the clearing alarm that appears when the condition is resolved.
Table A-48 SFAPP System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0543 | VLR Dynamic Learning is suspended | 0544 | VLR Dynamic Learning Started |
0646 | SFAPP Dynamic Learning Alarm Cleared | ||
0635 | SFLOG SYSTEM is not available | 0634 | SFLOG SYSTEM is available |
0639 | SFAPP Threshold Level Critical | 0640 | SFAPP Threshold Condition Cleared |
0644 | System SFAPP capacity Exceeded | 0636 | SFAPP is removed |
Major | Normal | ||
0638 | SFAPP Threshold Level2 Exceeded | 0640 | SFAPP Threshold Condition Cleared |
0643 | System SFAPP TPS Exceeded | 0642 | SFAPP Threshold normal |
0647 | EEDB Connectivity Down | 0648 | EEDB Connectivity Up |
Minor | Normal | ||
0637 | SFAPP Threshold Level1 Exceeded | 0640 | SFAPP Threshold Condition Cleared |
0642 | SFAPP Threshold normal | ||
0641 | SFAPP Capacity normal, card(s) abnormal | 0636 | SFAPP is removed |
0645 | LIM/SCCP card(s) denied SFAPP service |
A.49 SFLOG System Alarms
Table A-49 shows the critical SFLOG system alarm and the clearing alarm that appears when the condition is resolved.
Table A-49 SFLOG System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0627 | SFLOG SYSTEM is not available | 0628 | SFLOG SYSTEM is available |
0629 | SFLOG SYSTEM is removed |
A.50 SLK Alarms
Table A-50 shows the major, minor, and normal SLK alarms and the clearing alarm that appears when each condition is resolved.
Table A-50 SLK Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0201 | REPT-LKF: remote NE loopback | 0223 | REPT-LKF: remote NE loopback cleared |
0401 | Alarm cleared by deleting SLK | ||
0202 | REPT-LKF: HWP -too many interrupts | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0203 | REPT-LKF: lost data | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0204 | REPT-LKF: XER-ERM threshold exceeded | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0205 | REPT-LKF: APF - lvl-2 T1 expd (ready) | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0206 | REPT-LKF: APF -lvl-2 T1 expd(not ready) | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0207 | REPT-LKF: APF - lvl-2 T3 expired | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0208 | REPT-LKF: APF - lvl-2 T2 expired | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0209 | REPT-LKF: APF - failed proving period | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0210 | REPT-LKF: OSA - received SIO | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0211 | REPT-LKF: OSA - received SIN | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0212 | REPT-LKF: OSA - received SIE | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0213 | REPT-LKF: OSA - received SIOS | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0214 | REPT-LKF: ABN - rcvd 2 of 3 invalid BSN | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0215 | REPT-LKF: ABN - rcvd 2 of 3 invalid FIB | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0216 | REPT-LKF: remote congestion timeout | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0217 | REPT-LKF: XDA - excess acknowledge delay | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0218 | REPT-LKF: COO - rcvd changeover order | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0219 | REPT-LKF: false congestion restart | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0222 | REPT-LKF: remote FE loopback | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0224 | REPT-LKF: link test failed | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0230 | REPT-LKF: local blocked - thermal | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0232 | REPT-LKF: remote blocked | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0233 | REPT-LINK-MANUAV: local blocked | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0234 | REPT-LKF: RMI remote inhibited | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0235 | REPT-LINK-MGTINH: local inhibited | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0236 | REPT-LKF: not aligned | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0237 | REPT-LKF: LM Timer NO-CREDIT expired | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0238 | REPT-LKF: XDA-Timer NO-RESPONSE expired | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0239 | REPT-LKF: MBL - local processor outage | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0240 | REPT-LKF: rcvd remote processor outage | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0241 | REPT-LKF: rcvd remote out of service | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0242 | REPT-LKF: rcvd remote protocol error | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0243 | REPT-LKF: rcvd remote mgmnt initiated | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0244 | REPT-LKF: FAC - DS1/E1 LOS failure | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0245 | REPT-LKF: FAC - DS1/E1 LOF failure | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0246 | REPT-LKF: FAC - DS1/E1 LCD failure | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
0247 | REPT-LKF: XER - ISERM threshold exceeded | 0200 | RCVRY-LKF: link available |
0401 | Alarm cleared by deleting SLK | ||
Minor | Normal | ||
0116 | Link expected IP TPS threshold exceeded | 0119 | LinkIPTPS threshold normal |
0477 | Congestion: Copy Function De-activated | 0479 | Link not monitored |
0531 | Insufficient HW Copy Function Inhibited | 0478 | Copy Function Activated |
0479 | Link not monitored | ||
0583 | Unexpected SAM Received | 0584 | Expected SAM Received |
Normal | Normal | ||
0264 | REPT-LINK-CGST: congestion level 0 to 1 | 0269 | RCVRY-LINK-CGST:congestion has cleared |
0265 | REPT-LINK-CGST: congestion level 1 to 2 | 0268 | RCVRY-LINK-CGST:congestion level 2 to 1 |
0269 | RCVRY-LINK-CGST:congestion has cleared | ||
0266 | REPT-LINK-CGST: congestion level 2 to 3 | 0267 | RCVRY-LINK-CGST:congestion level 3 to 2 |
0269 | RCVRY-LINK-CGST:congestion has cleared | ||
0270 | REPT-LINK-CGST: discard level 0 to 1 | 0275 | RVCRY-LINK-CGST: discard has cleared |
0271 | REPT-LINK-CGST: discard level 1 to 2 | 0274 | RVCRY-LINK-CGST: discard level 2 to 1 |
0275 | RVCRY-LINK-CGST: discard has cleared | ||
0272 | REPT-LINK-CGST: discard level 2 to 3 | 0273 | RVCRY-LINK-CGST: discard level 3 to 2 |
0275 | RVCRY-LINK-CGST: discard has cleared |
A.51 <subsystem> System Alarms
Table A-51 shows system alarms that may occur for different subystems and the clearing alarm that appears when each condition is resolved. The name of the subsystem varies.
Table A-51 <subsystem> System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0592 | <subsystem> Subsystem is not available | 0595 | <subsystem> Subsystem is available |
0594 | <subsystem> Subsystem normal, card(s) abnormal | ||
0593 | <subsystem> Subsystem is disabled | 0596 | <subsystem> Subsystem is removed |
0594 | <subsystem> Subsystem normal, card(s) abnormal | ||
Major | Normal | ||
0598 | <subsystem> degraded, card(s) abnormal | 0595 | <subsystem> Subsystem is available |
0596 | <subsystem> Subsystem is removed | ||
Minor | Normal | ||
0594 | <subsystem> Subsystem normal, card(s) abnormal | 0595 | <subsystem> Subsystem is available |
0596 | <subsystem> Subsystem is removed |
A.52 System Alarms
Table A-52 shows the critical, major, and minor System alarms and the clearing alarm that appears when each condition is resolved.
Table A-52 System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0308 | Node isolated due to SLK failures | 0309 | Node is no longer isolated |
0368 | Temp Keys(s) have expired. | 0366 | Temp Key(s) expiration alarm cleared |
0438 | Degraded Mode, Invalid OAM HW config | 0439 | Exiting Degraded Mode |
0561 | Can't establish Hi Bit rate;All HW OK | 0562 | Hi Bit rate established |
Major | Normal | ||
0011 | Entering forced simplex mode | 0018 | Exiting forced simplex mode |
0367 | Temp Keys(s) expiring soon. | 0366 | Temp Key(s) expiration alarm cleared |
0911 | Dynamic database is inconsistent | 0912 | Dynamic database is now consistent |
Minor | Normal | ||
0302 | Cooling fan failure | 0303 | Cooling fans normal |
A.53 System GPL Alarms
Table A-53 shows the minor GPL alarms and the clearing alarm that appears when each condition is resolved.
Table A-53 System GPL Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Minor | Normal | ||
0143 | System release GPL(s) not approved | 0142 | System release alarm cleared |
0144 | System release version unknown |
A.54 T1 Port Alarms
Table A-54 shows the major T1 alarms and the clearing alarm that appears when each condition is resolved.
Table A-54 T1 Port Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0369 | REPT-T1F:FAC-T1 unavailable | 0380 | RCVRY-T1F:FAC-T1 available |
0376 | REPT-T1F:FAC-T1 LOS failure | ||
0377 | REPT-T1F:FAC-T1 LOF failure | ||
0378 | REPT-T1F:FAC-T1 Remote Alarm | ||
0379 | REPT-T1F:FAC-T1 Alarm |
A.55 Terminal Alarms
Table A-55 shows the minor Terminal alarm and the clearing alarm that appears when the condition is resolved.
Table A-55 Terminal Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Minor | Normal | ||
0048 | Terminal failed | 0046 | Terminal enabled |
A.56 V-Flex System Alarms
Table A-56 shows the major and minor X-LIST alarms and the clearing alarm that appears when each condition is resolved.
Table A-56 V-Flex System Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Critical | Normal | ||
0551 | V-Flex Subsystem is not available | 0554 | VFLEX Subsystem is available |
0555 | VFLEX Subsystem is removed | ||
0552 | VFLEX Subsystem is disabled | 0554 | VFLEX Subsystem is available |
0555 | VFLEX Subsystem is removed | ||
Major | Normal | ||
0556 | V-Flex Subsystem degraded, card(s) abnormal | 0554 | VFLEX Subsystem is available |
0555 | VFLEX Subsystem is removed | ||
Minor | Normal | ||
0553 | VFLX Subsystem normal, card(s) abnormal | 0554 | VFLEX Subsystem is available |
0555 | VFLEX Subsystem is removed |
A.57 X-LIST Alarms
X-LIST Alarms shows the major and minor X-LIST alarms and the clearing alarm that appears when each condition is resolved.
Table A-57 X-LIST Alarms
UAM | Text | UAM | Text |
---|---|---|---|
Major | Normal | ||
0338 | X-LIST space full-entry(s) discarded | 0339 | X-LIST space full condition abated |
Minor | Normal | ||
0321 | X-LIST occupancy threshold exceeded | 0322 | X-List occupancy below threshold |