5.17 disp-bp

Use this command to display currently active breakpoints in the communication and application processors.

Parameters

card (optional)
This parameter specifies the card location, in the form of GPLID–Subsystem ID.
Range: GPLID-Subsystem ID
GPLID
atmhc, deirhc, erthc, glshc, hipr2, ipghc, iplhc, ipsg, ipshc, mcphc, oamhc, pktgen, sccphc, siphc, ss7hc, utility
Subsystem ID
a, b, act, stb, all

The oamhc GPL can be specified with any of the subsystem IDs. For all other GPLs, only the all subsystem ID is valid.

imt (optional)
The IMT address of the card.
Range:
0 - 254
loc (optional)
The card location as stenciled on the shelf of the system.
Range:
1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1109, 1110, 1209, 1210, 1309, 1310, 2109, 2110, 2209, 2210, 2309, 2310, 3109, 3110, 3209, 3210, 3309, 3310, 4109, 4110, 4209, 4210, 4309, 4310, 5109, 5110, 5209, 5210, 5309, 5310, 6109, 6110, 1113, 1115
proc (optional)
This parameter specifies the processor type.
Range:
appl
Application processor
com
Communication processor
Default:
appl
ueng (optional)
The microengine number.

This parameter is valid only on IXP-based cards. If this parameter is not specified for IXP-based cards, then the command is assumed to be intended for the ARM processor in the IXP chip.

Range:
0 - 5

Example

disp-bp:loc=1109:ueng=3

Dependencies

The loc, imt, or card parameter must be specified.

2214 E2214 Cmd Rej: Missing parameter - CARD, LOC, or IMT

Only one of the loc, imt, and card parameters can be specified in the command.

2217 E2217 Cmd Rej: More than one of CARD, LOC, and IMT specified

The imt parameter allows this command to be entered for a card that has not been configured in the system.

N/A N/A

The ueng parameter can be specified only for IXP-based cards.

4151 E4151 Cmd Rej: UENG parameter is invalid for this card

The oamhc GPLID accepts all subsystem values; all other GPLIDs accept only the all subsystem value.

N/A N/A

The card location specified by the loc parameter must be in the database.

2101 E2101 Cmd Rej: Card location is unequipped

Values of 1114, 1116, 1117, and 1118 cannot be specified for the loc parameter.

2212 E2212 Cmd Rej: Invalid card type for this command

Notes

None

Output

These examples are for x86-based cards:

disp-bp:card=ss7ansi-all

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    SDS Installed Breakpoint Report from IMT Address H'00f4  
    Brkpoint-Addr Memory-Dump-Addr Condition-1 Condition-2 Repeat-Count  
    ------------- ---------------- ----------- ----------- ------------ 
    H'003a-H'0001                  ANY         ANY               0 

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0  
    SDS Installed Breakpoint Report from IMT Address H’000a  
    BP Address Memory-Dump Address       Conditions         Rpt Ct Ind  
    ---------- ------------------------- ------------------ ------ --- 
    H’0000a974 H’000c030c                1- ANY               3     1
       Code Breakpoint                   2- ANY 
    H’0000a975                           1- ANY              PERM   0
       Data Write - WORD                 2- ANY 
    H’0000a976                           1- ANY               15    0
       Any Access - DWORD                2- ANY 
    H’0000a977                           1- ANY              PERM   0
       Data Read - BYTE                  2- ANY 

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    80386/80486 Debug Registers in Use: DR0 DR2 DR3 
;
disp-bp:card=vsccp-all:

    rlghncxa03w 01-03-22 21:14:58 EST EAGLE5 31.3.0 
    SDS Installed Breakpoint Report from IMT Address H'0005 
    BP Address Memory-Dump Address       Conditions        Rpt Ct Ind 
    ---------- ------------------------- ----------------- ------ --- 
    H'0000a974                           1- ANY            1       0 
    Code Breakpoint                      2- ANY 
;

These examples are for IXP-based cards:

disp-bp:loc=1109

    tekelecstp 05-01-10 13:58:45 GMT EAGLE5 33.0.0 
    SDS Installed Breakpoint Report from IMT Address H'00ff 

    BP Address Memory-Dump Address Conditions            Rep  Ind CPU 
    ---------- ------------------- --------------------- ---- --- ------ 
    H'000401000 R11+H'0000ffff     1- R15 > H'ffffffff     2   0    ARM
       Any Access -                2- R0 <= H'0000ffff
       Data value: H'00000000 Data Mask: H'ffffffff
disp-bp:loc=1109:ueng=3

    tekelecstp 05-01-10 13:58:45 GMT EAGLE 33.0.0 
    SDS Installed Breakpoint Report from IMT Address H'00ff 

    BP Address Memory-Dump Address Conditions            Rep  Ind CPU 
    ---------- ------------------- --------------------- ---- --- ------ 
    H'00235000 H'00020044          1- ANY                PERM 1   UENG 3
       CODESW Breakpoint           2- ANY                         CTX 2 
;

Related Topics