5.2 act-ip-lnk

Use this command to activate an IP link and put the link into service. The state of the link is changed from OOS-MT-DSBLD (Out-Of-Service-Maintenance-Disabled) to OOS-MT (Out-Of-Service-Maintenance), IS-ANR (In-Service-Abnormal) or IS-NR (In-Service-Normal).

Note:

The specified card must be Active before the command can be executed. If the card boots, then the status of the IP link will be reset.

Parameters

loc (mandatory)
The card location as stenciled on the shelf of the system.
Range:
1101 - 1108, 1111 - 1112, 1201 - 1208, 1211 - 1218, 1301 - 1308, 1311 - 1318, 2101 - 2108, 2111 - 2118, 2201 - 2208, 2211 - 2218, 2301 - 2308, 2311 - 2318, 3101 - 3108, 3111 - 3118, 3201 - 3208, 3211 - 3218, 3301 - 3308, 3311 - 3318, 4101 - 4108, 4111 - 4118, 4201 - 4208, 4211 - 4218, 4301 - 4308, 4311 - 4318, 5101 - 5108, 5111 - 5118, 5201 - 5208, 5211 - 5218, 5301 - 5308, 5311 - 5318, 6101 - 6108, 6111 - 6118, 1113, 1115
port (mandatory)
Ethernet interface Port ID.
Range:
a
IP Port A
b
IP Port B
c
IP Port C
d
IP Port D
fca
Fast Copy Port A
fcb
Fast Copy Port B

Example

act-ip-lnk:loc=1102:port=a

act-ip-lnk:loc=1203:port=fca

act-ip-lnk:loc=1103:port=c

act-ip-lnk:loc=1202:port=d

Dependencies

The value specified for the loc parameter must refer to one of the following cards, and the referenced card must be equipped:

  • E5-ENET-B card running the EROUTE, IPGWx, IPLIMx, or IPSG application
  • IPSM card
  • E5-SM4G or E5-SM8G-B card running the VSCCP application
  • E5-OAM card running the OAMHC application
  • E5-MCPM-B
  • SLIC card

A valid value must be specified for the loc parameter.

2376 E2376 Cmd Rej: Specified LOC is invalid

The value specified for the port parameter must be supported by the card:
  • port A - E5-OAM card running OAMHC application, IPSM card, E5-MCPM-B card
  • port A, B - E5-ENET-B card running the EROUTE or IPLIMx application, E5-SM4G or E5-SM8G-B card running the VSCCP application
  • port A, B, FCA, FCB - E5-ENET-B card running the IPGWx or IPSG application
  • port A, B, C and D are valid for SIP/ENUM/DEIR application running on SLIC card.

2975 E2975 Cmd Rej: Specified Port is not supported

The card at the specified location must be configured.

2144 E2144 Cmd Rej: Location invalid for hardware configuration

The card in the specified location must be Active before this command can be executed.

2387 E2387 Cmd Rej: Card is not in service

Notes

The act-ip-lnk/dact-ip-lnk commands were created as debug means - aids to turn off or disable the IP interface to troubleshoot network problems, specifically to allow the operator to troubleshoot IP network flooding issues that can cause EAGLE cards to boot repeatedly while trying to come up. These commands should NOT be used for general maintenance actions since they have not been rigorously tested and their usage should be limited to situations like described above.

Interface A/D is used for ExAP connectivity and interface B/C is used for the signaling network on the SLIC card running the SIP/ENUM/DEIR application.

Output

act-ip-lnk:loc=1101:port=a
Command Accepted - Processing

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    act-ip-lnk:loc=1101:port=a
    Command entered at terminal #1.
;

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    Activate IP link message sent to card.
;

    tekelecstp 11-08-16 19:52:01 MST  EAGLE 44.0.0
    Command Completed.
;
act-ip-lnk:loc=1103:port=c
Command Accepted - Processing

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    act-ip-lnk:loc=1103:port=c
    Command entered at terminal #18.
;

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    Activate IP link message sent to card.
;

    tekelecstp 16-05-25 03:48:33 MST   EAGLE 46.4.0.0.0-69.1.0
    Command Completed.
;