L
- LACP
- using a switch with
Using a Switch With the Link Aggregation Control Protocol
- using a switch with
- link aggregation
- example of adding a link to an aggregationAdding a Link to an Aggregation
- example of deleting a link aggregationDeleting a Link Aggregation
- example of adding a link to an aggregation
- Link Aggregation Control Protocol (LACP) SeeLACP
- link aggregationsLink Aggregations
- adding datalinksHow to Add a Link to an Aggregation
- benefitsBenefits of Link Aggregation
- combined use with VLANsUse Case: Combining Link Aggregations and VLAN Configurations
- creatingHow to Create a Link Aggregation
- deletingHow to Delete a Link Aggregation
- DLMP aggregationsDatalink Multipathing Aggregations
- example of removing a link from an aggregationRemoving a Link From an Aggregation
- feature comparison of trunk and DLMP aggregationsComparing Trunk and DLMP Aggregation
- featuresBenefits of Link Aggregation
- IPMP, comparison withLink Aggregations and IPMP: Feature Comparison
- overviewOverview of Link Aggregations
- requirementsRequirements for Link Aggregations
- switching between DLMP and trunk aggregationsHow to Switch Between Link Aggregation Types
- trunk aggregationsTrunk Aggregations
- adding datalinks
- Link Layer Discovery Protocol SeeLLDP
- link layer discovery protocol SeeLLDP
- link properties
- setting for a bridgeSetting Link Properties for a Bridge
- setting for a bridge
- link state notificationRequirements for Link Aggregations
- link-based failure detectionLink-Based Failure Detection
- LLDP
- agent modesLLDP Agent Modes
- auto-enable-agentsEnabling LLDP on the System
- components in Oracle SolarisComponents of an LLDP Implementation
- defining TLV valuesHow to Define TLV Units
- disablingDisabling LLDP
- displaying advertised informationDisplaying the Advertised Information
- displaying statisticsDisplaying LLDP Statistics
- enablingEnabling LLDP on the System
- enabling for specific portsHow to Enable LLDP for Specific Ports
- enabling globallyHow to Enable LLDP Globally
- example of adding optional TLV unitsAdding Optional TLV Units to an LLDP Packet
- example of customizing the auto-enable-agents SMF propertyCustomizing the auto-enable-agents SMF Property
- example of defining TLV valuesDefining TLV Values for the syscapab and mgmtaddr TLV
Units
- example of displaying advertised informationDisplaying Advertised LLDP Agent Information
- example of displaying selected statisticsDisplaying Selected LLDP Packet Statistics
- example of displaying statisticsDisplaying LLDP Packet Statistics
- example of displaying the chassis ID and port IDDisplaying the Chassis ID and Port ID
- example of enabling LLDP on multiple datalinksEnabling LLDP on Multiple Datalinks
- global TLV units
- installingHow to Install the LLDP Package
- lldpd daemonComponents of an LLDP Implementation
- management information base (MIB)Information Sources of the LLDP Agent
- monitoring agentsMonitoring LLDP Agents
- optional TLV unitsOptional TLV Units
- per-agent TLV units
- SMF property forEnabling LLDP on the System
- specifying agent TLV unitsHow to Specify TLV Units for the LLDP Packet of an Agent
- agent modes
- LLDP SMF serviceComponents of an LLDP Implementation
- lldpadm commandComponents of an LLDP Implementation
- reset-agentpropDisabling LLDP
- set-agentprop
- set-agenttlvprop
- show-agenttlvprop
- show-tlvpropHow to Define TLV Units
- reset-agentprop
- load balancing
- trunk aggregationsDefining Aggregation Policies for Load Balancing
- trunk aggregations