Known Issues
The following table lists the known issues in version S-Cz9.0.0. You can reference known issues by Service Request number and you can identify the issue, any workaround, when the issue was found, and when it was fixed using this table. Issues not carried forward in this table from previous Release Notes are not relevant to this release. You can review delivery information, including defect fixes in the S-Cz9.0.0 Build Notes.
ID | Description | Severity | Found In |
---|---|---|---|
35649015 | When Teams places a call on hold, SBC is not generating an RTCP, causing Teams endpoint to drop the call after 3 minutes. | 3 | S-Cz9.2.0p2 |
33600407 | When IPv4 and IPv6 addresses are
added consecutively on the hip-ip-list and icmp-address of same
network-interface, followed by save/activate, the configuration
change is eventually activated but the SBC will get into unsteady
state, followed by below events on the console:
unregister_netdevice: waiting for <interface:id> to become free.Usage count = 1 Workaround: Add IPv4 and IPv6 address on the hip-ip-list and icmp-address separately and activate them individually i.e. activate the first config change/addition and then add and activate the second config change. |
2 | S-Cz8.4.0 |
33190562 | On the AP3950 and AP4900, in <
0.1% of reboots, the platform gets stuck and does not reach the ACLI
prompt.
Workaround: perform a power cycle to successfully reboot the system. |
2 | S-Cz9.0.0p1 |
33059603 | On the AP3900, AP3950, and AP4900,
when performing quickly successive switchovers, an active system
system may not synchronize and go OOS after a failover.
Workaround: Set the gateway heartbeat interval timeout value to 10 seconds with 3 gateway heartbeat retries. |
3 | S-Cz9.0.0p1 |
32742216 | The Acme Packet 1100, 3900 and 4600 as well as all software-only deployments do not support any Media Policing configuration. | 3 | S-Cz8.4.0 |
32077115 | For Hairpin/Spiral call scenarios,
the hide-egress-media-update parameter under media-sec-policy is not
supported.
In addition, you must reboot the SBC when you change the hide-egress-media-update parameter under the media-sec-policy, inbound subelement. This parameter is not RTC supported. Oracle recommends you use the hide-egress-media-update parameter under the realm-config only. |
3 | S-Cz9.0.0 |
32565921 | The acquire-config process fails if
your configuration includes an acp-tls-profile. The system does,
however, successfully synch this profile after HA is established.
Workaround: Disable your acp-tls-profile on the active system before performing an aquire-config procedure. Re-enable this profile after aquire-config completes successfully. |
3 | S-Cz9.0.0 |
None | This version's enhancement to SMP-Aware Task Load Limiting, which adds a second parameter to the sip-config load-limit option, is currently not supported. | N/A | S-Cz7.4.0 |
None |
Re-balancing is unavailable on the OCSLB when running an Acme Packet 6300 as a cluster member. Set the SLB cluster-config, auto-rebalance parameter to disabled to use an Acme Packet 6300 as a cluster member from that SLB. | N/A | S-Cz730 |
None |
The system does not support SIP-H323 hairpin calls with DTMF tone indication interworking. | N/A | S-CZ720 |
None |
The SBC stops responding when
you configure an H323 stack supporting SIP-H323-SIP calls with the
max-calls parameter set to a value that is less
than the q931-max-calls parameter.
Workaround: For applicable environments, configure the H323 stack max-calls parameter to a value that is greater than its q931-max-calls parameter. |
N/A | S-CZ7.4.0 |
None | The system does not support HA Redundancy for H.323 calls. | N/A | N/A |
27699451 |
Oracle qualified the QSFP interface for the OCSR operating over the Oracle X7-2 platform for a single QSFP port operating in 4-port mode. Specifically, 4 media interfaces successfully map to the second port of the QSFP interface using a Hydra cable as physical connections to 10G switch ports. | 3 | S-Cz8.1.0 |
26316821 |
When configured with the 10 second QoS update mechanism for OCOM, the SBC presents the same codec on both sides of a transcoding call in the monitoring packets. You can determine the correct codecs from the SDP in the SIP Invite and 200 OK. |
3 | S-Cz8.0.0p1 |
The SBC dead peer detection does not work with IKEv1. | 3 | S-Cz8.4.0 | |
28539190 | When operating as a VNF and using Mellanox interface cards, the OCSBC does not use the Host In Path (HIP) configuration to restrict management traffic, Instead the system allows any traffic over the interface. | 3 | S-Cz8.2.0 |
28617865 | This version of the OCSBC is not supported as a VNF over VMware using Mellanox interface cards. | 3 | S-Cz8.2.0 |
29170419 | In long call scenarios, the SBC is not sending the expected refresh before the Session-Expires: header value time is up for SUBSCRIBE messages. | 2 | S-Cz8.2.0 |
30643522 |
Starting with S-Cz8.3.0m1p2, Lawful
Intercept users cannot modify LI configuration with the Session
Delivery Manager.
Workaround: LI Configuration must be performed through the ACLI. |
4 | S-Cz8.3.0m1p2 |
Resolved Known Issues
ID | Description | Severity | Found In | Fixed In |
---|---|---|---|---|
35614646 | Certain RFC2833/telephone-event sequences generated by customer endpoints may not be properly detected, reported, or re-transmitted by the SBC, resulting in missing DTMF digit(s). | 2 | S-Cz9.0.0p10 | S-Cz9.0.0p12 |
32709550 | When operating over the Azure platform, the SBC displays an inordinate number of kernel messages during the bootup process. You can safely ignore these messages. | 3 | S-Cz9.0.0 | S-Cz9.0.0 |
26323802 |
The 10s QoS interim feature includes the wrong source IP address as the incoming side of a call flow. The issue does not prevent successful call and QoS monitoring. For monitoring and debugging purposes, you can find the source IP in the SIP messages (INVITE/200OK). |
3 | S-Cz8.0.0p1 | S-Cz9.0.0p5 |
26497348 |
When operating in HA mode, the SBC may display extraneous "Contact ID" output from the show sipd endpoint-ip command. You can safely ignore this output. | 3 | S-Cz8.0.0 | S-Cz9.0.0p5 |
28658810 | When operating as a VNF and using Mellanox interface cards, the OCSBC does not support any other type of card for media interfaces. (If any media interface uses a Mellanox card, all media interfaces must use a Mellanox card.) | 3 | S-Cz8.2.0 | S-Cz9.1.0 |
34022202 | It is possible that the system
(active or standby) can experience cores reaching 100% CPU
utilization when running periodic scripts which
connect/disconnect via SSH to the SBC. This is observed in the
display-alarm output.
Workaround:
If the issue is encountered on the
standbysystem:
|
2 | S-Cz9.0.0p3 | S-Cz9.0.0p4 |
33434641 | If local-port-match value is set under security-policy, and local-port-match-max is not set, then SBC processes traffic considering full port range. SBC considers the default value of local-port-match-max (i.e. 65535) and applies the specific action mentioned under security-policy to full port range. Configure the local-port-match-max or remote-port-match-max value to set a new port range or set same value for local-port-match and remote-port-match-max to configure a single port. | 2 | S-Cz8.4.0p4 | S-Cz8.4.0p9 |
32181987 | Do not copy/paste characters into
a configuration menu and attempt to edit the copied text. This
applies to both console and SSH sessions.
Workaround: Edit the data before copy/paste. |
3 | S-Cz8.4.0 | S-Cz9.0.0p3 |
33454565 | The AWS SPL NAT does not function with Scz9.0.0p1, hence you need to load all SPL files by default but not activate them using the spl-autoload-for-sbc option at global spl-config level. You can also activate a specific SPL. There can be issues if you select multiple preloaded SPLs or enable the spl-autoload-for-sbc option with a bulky configuration. With Scz9.0.0p2 and newer, you need not configure these options. | 3 | S-Cz9.0.0p1 | S-Cz9.0.0p2 |
32535426 | The show temperature output will
display different values compared to releases older than
S-Cz8.3.0. Starting with S-Cz8.3.0, the temperature queries via
ACLI and SNMP are reporting more accurate values.
|
3 | S-Cz8.1.0 | S-Cz8.3.0 |
33059603 | On the AP3900, AP3950, and
AP4900, when performing quickly successive switchovers, an
active system system may not synchronize and go OOS after a
failover.
Workaround: Set the gateway heartbeat interval timeout value to 10 seconds with 3 gateway heartbeat retries. |
3 | S-Cz9.0.0p1 | S-Cz9.0.0p2 |
ACMECSBC-35051 | The SBC does not support HA replication of a Wildcard PAU. | 3 | S-Cz9.0.0 | S-Cz9.0.0p1 |
32939208 | You cannot set the SBC
ikev2-ipsec-wancom0-params parameters
using SDM due to issues with the configuration of the
rekeyfuzz and
localip parameters. Note these
parameters have defaults or "0" and "empty" respectively. You
can, however, configure these values from the SBC .
You cannot set the OCSBC ikev2-ipsec-wancom0-params via SDM due to issues in configuration of parameters rekeyfuzz and localip, which have defaults or "0" and "empty" respectively, using OCSDM. Furthermore, if you change the values for rekeyfuzz and localip, you cannot change them back to their defaults. Workaround for changing these parameters' values back to their defaults:
|
3 | S-Cz9.0.0 | S-Cz9.0.0p1 |
24574252 |
The show interfaces brief command incorrectly shows pri-util-addr information in its output. | 3 | S-Cz7.4.0 | S-Cz9.0.0 |
ACMECSBC-38270 | Do not configure STIR over TLS. This configuration causes the system to crash. | 3 | S-Cz9.0.0 | S-Cz9.0.0p1 |
32939113 | Do not configure the
auth-user-lookup parameter within the
local-policy,
policy-attribute without already
having:
Workaround: Configure the applicable sip-interface and associated realms before you configure the local-policy, policy-attribute, auth-user-lookup parameter. |
3 | S-Cz9.0.0 | S-Cz9.0.0p1 |
29439964 | ACLI Users will receive an error on the output of the show registration sipd by-user command. | 4 | S-Cz8.2.0 | S-Cz8.4.0 |
32534935 | Media is not resumed after RBT playback for transcoded calls on vSBC. Avoid upgrading to releases where this bug is open if your deployment uses a vSBC with Transcoding and is configured to use Ringback-Trigger values. | 3 | S-Cz8.4.0M0P4 | S-Cz9.0.0 |
31163030 | In VOLTE deployments with registration refreshes, you may see unusually large numbers in the alloc and usage count fields while executing the show buffers command. This is a known statistics accounting issue. | 4 | S-Cz8.3.0 | S-Cz9.0.0 |
31315823 |
When running IMS-AKA over UDP on virtual SBCs, IMS-AKA registrations may not succeed. Registration failure can also cause associated calls to fail. Oracle has observed this only happens after a system reboot. Oracle has also observed that performing a Save and Activate command sequence after a reboot ensures these registrations are successful. If you are running IMS-AKA over UDP on virtual SBCs, perform a Save and Activate command sequence after system reboot to ensure successful IMS-AKA registrations. |
3 | S-Cz8.4.0 | S-Cz9.0.0 |
31828563 | While using STIR/SHAKEN, Acme Packet 4600 performance is capped at 330 CPS, and Acme Packet 6350 performance is capped at 1200 CPS for both dual and quad NIU cards. | 3 | S-Cz8.4.0M0P2 | S-Cz9.0.0 |
Do not upgrade to S-Cz9.0.0
directly from S-Cz8.4.0p4, S-Cz8.4.0p5 or any S-Cz8.4.0p5 OOC
patches up to S-Cz8.4.0p5B. If running these versions, upgrade
to S-Cz8.4.0p5C before upgrading to S-Cz9.0.0. Upgrading
directly from these versions may cause the system to crash.
When upgrading from these versions, upgrade to S-Cz8.4.0p5C first. |
3 | S-Cz8.4.0M0P4 | S-Cz8.4.0M0P5 | |
29881449 |
The DSP used by the OCSBC has a vendor firmware defect that causes failures with the T.38 codec. If you are using the T.38 codec, you may experience minimal media losses on those calls. This problem may also cause the OCSBC to reboot. | 3 | S-Cz8.1.0m1p9 | S-Cz8.4.0p4 |
32517222 | Media is not resumed after RBT playback for transcoded calls on vSBC. Avoid upgrading to releases where this bug is open if your deployment uses a vSBC with Transcoding and is configured to use Ringback-Trigger values. | 3 | S-Cz8.4.0M0P4 | S-Cz8.4.0P4A |
Please see the section on Upgrades For Configurations that Include Signaled IPSec Tunnels and LI Configurations in Upgrade Downgrade Caveats in this document for an explanation of this issue. |
3 | S-Cz8.4.0 | S-Cz9.0.0 | |
32243204 | STIR/SHAKEN entitlement is not available when system is set up as a Peering Session Border Controller product. | 2 | S-Cz8.4.0p2 | S-Cz8.4.0p4 |
32056356 |
While performing VoLTE Accounting on a 3G-to-4G MT call, the SBC incorrectly populates VSA ID 69 with the P-Asserted-Identity (PAI) retrieved from the response. This identifies the called side. Within the context of a mobile terminating call, the SBC should be identifying the caller, populating this VSA with the PAI retrieved from the INVITE. Workaround—You can correct this by setting the unidirectional-p-asserted-id option in the applicable account-config to yes. |
2 | S-Cz8.4.0 | S-Cz8.4.0p4 |
31812964 31926021 31918592 |
The SBC incorrectly exhibits the following 3 incorrect behaviors with the PCRF during Register and Message call flows:
Workaround—You can correct this by setting the diam-rx-strict-compliance option to the applicable ext-policy-server to enabled. When you set this option, you can correct the three issues above so that the SBC performs the following:
|
3 | S-Cz8.4.0 | S-Cz8.4.0p4 |
28618563 |
The system is not populating the Username AVP in Accounting Requests (ACRs) correctly. When triggered by an INVITE, these AVPs contain only the "@" sign. They do not include the username and domain name portion of the URL. | 3 | CZ8.1.0m1 | S-Cz8.4.0 |
31726575 | Do not configure
sip-advanced-logging if you expect any auth-invite call flows
(401/407). If you are upgrading to S-Cz8.4.0p2 or later, and
your configuration includes conditional logging (session-router,
sip-advanced-logging, state=enabled), you must first remove
sip-advanced-logging from the config, otherwise calls will
fail.
|
2 | S-Cz8.4.0p2 | S-Cz8.4.0p4 |
32049267 | Do not configure AEAD_AES_256_GCM cipher in the sdes-profile, crypto-list parameter, or the system will crash. | 3 | S-Cz8.4.0p3 | S-Cz8.4.0p4 |
31384643 |
During the testing of this release Oracle identified a pre-existing issue in the code where adding an LI warrant during a period of heavy SIP load may cause the system to stop responding, which results in a switchover. This issue exists in prior releases and will be addressed in an upcoming 8.4 patch. If you have not encountered this issue in the past, it is unlikely that you will encounter it now. System Impact: If you add an LI warrant while the SBC is under heavy load from SIP traffic, a mid-call intercept operation may not occur after the addition (causing the SBC to stop responding). If the SBC stops responding a switchover will occur, but the warrant will have been added correctly. The issue can be mitigated by performing addition of LI warrants during off-peak times, such as maintenance windows. |
3 | S-Cz8.4.0 | S-Cz8.4.0p2 |
30520108 |
Upon registering 100k or more IMS-AKA user registrations, and handling large numbers of VoLTE calls and registration refreshes, in excess of 8k for example, a vSBC may hang. At this point, you would find the vSBC unresponsive and inaccessible. An example of conditions when this may occur includes:
Reboot the system from the hypervisor to recover from this issue. |
N/A | N/A | S-Cz8.3.0m1p5 |
30364057 |
Do not use DNS for multiple
services on the OCSBC simultaneously. DNS service operates on
the OCSBC normally when you configure it for a single purpose.
When you configure it for multiple purposes, however, lookups do
not complete correctly.
Workaround: An example of this would be configuring DNS for both PCRF and ENUM services. You can mitigate this issue by configuring the local routing table with ENUM lookups. |
3 | S-Cz8.3.0p7 | S-Cz8.3.0m1p5 |
29862440 |
When transcoding from T.38 to G711FB, the OCSBC includes multiple (for example 2) m-lines in the SDP when there are multiple (for example 2) c-lines in the source SDP. This happens even if you have set the fax-single-m-line parameter in the applicable codec-policy to present a single m-line. Workaround: Configure an ingress HMR to remove all but 1 c-line from the incoming SDP. |
3 | S-Cz7.4.0m1p8 | S-Cz8.3.0m1p3 |
30158557 |
Under high media loads that include AMR/AMR-WB to PCMA transcoding, the 10G port on the Acme Packet 6300 is experiencing packet loss and, therefore media MOS degradation. | 2 | S-Cz8.1.0m1p16 | S-Cz8.4.0 |
30444535 |
When configured for the minimum TCP disconnect time, the default for network-parameters, the OCSBC takes an unexpectedly long time before attempting to create a socket and connect. When using the defaults to create and connect using the minimum amount of time, this process takes 18 seconds instead of 9. | 3 | N/A | S-Cz8.3.0m1p3 |
29846828 |
The OCSBC stops generating registration refreshes after 12 hours for Surrogate Agents. After a reboot, the OCSBC attends to registration and refreshes correctly using the new Call ID for 12 more hours. | 2 | E-Cz8.1.0m1p8 | S-Cz8.1.0m1p22 |
30330778 |
The OCSBC cannot forward a call that uses a TEL-URI and includes the routing number (rn) parameter. Depending on your routing configuration, the OCSBC may reject these call with a 404 Not Found/No Route to Destination. The OCSBC forwards these portability scenarios properly when they present an R-URI. | 1 | S-Cz7.4.0m2p4;8.1.0m1p18 | S-Cz8.1.0m1p23 |
29779932 |
The OCSBC uses a Diffie Hellman algorithm that conflicts with that of the 10.4 Solaris SFTP server. As a result, both CDR and HDR transfers to these servers fail. Do not use the Solaris 10.4 SFTP server with the OCSBC. |
1 | S-Cz8.1.0m1p9, S-Cz8.3.0p7 | S-Cz8.3.0m1p4 |
29913123 |
NMC causes the Acme Packet 6350 to switchover when NMC gets its first traffic match. | 2 | S-Cz8.1.0M1P9 | S-Cz8.3.0m1p3 |
29403076 |
When generating HDR reports and SNMP output on resource utilization that includes threads, the OCSBC omits the thread name, leaving the applicable field and OID empty. | 3 | S-Cz8.1.0M1P9 | S-Cz825p3 |
310398.2.0 | When mid-call Lawful Intercept is enabled, and the SBC has not started intercepting particular sessions, those sessions will not be replicated on the standby. If a switchover occurs, affected calls could be dropped. | 3 | S-Cz8.3.0m1p2 | S-Cz8.4.0 |
28157960 |
When setting up a SIPREC session, the SBC sets up 1-way audio if the far end offers an odd port number in the m line. |
2 | S-Cz8.0.0 | S-Cz8.3.0m1p8 |
26669090 |
The SBC dead peer detection does not work with IPv4. | 3 | S-Cz8.0.0 | Could not reproduce - S-Cz8.4.0 |
22322673 |
When running in an HA
configuration, the secondary SBC might go out of
service (OoS) during upgrades, switchovers, and other HA
processes while transitioning from the "Becoming Standby" state.
Oracle observes such behavior in approximately 25% of these
circumstances. You can verify the issue with log.berpd, which
can indicate that the media did not synchronize.
Workaround: Reboot the secondary until it successfully reaches the "Standby" state. |
3 | S-Cz7.3.0P1 | S-Cz8.0.0 |
29931732 |
The embedded communications monitor probe does not send IPv6 traffic to the Oracle Communications Operations Monitor's mediation engine. | 3 | S-Cz8.0.0 | S-Cz8.3.0m1p4 |
30375697 | Infrequently during race conditions, the number of SIP registration entries on the active and standby SBCs differs, with the standby SBC containing fewer entries. When this happens and a switchover occurs, some endpoints are unable to receive calls until the endpoint re-registers. Increase Journal index size and optimize the Journal management code to avoid this. | 2 | S-Cz8.1.0m1p18 | S-Cz8.1.0m1p18b |
30544663 | When a session add action is
executed and the session is not found in the sipProxy, a new Sip
Session and two Sip Dialogs are created and cross referenced and
the buffer from the active is loaded. If the load fails, the
update function exits and the SipSession and SipDialogs are left
dangling and create a memory leak.
Workaround: To avoid this memory leak, successfully load the buffer BEFORE creating the session and dialogs. Monitor the standby SBC's memory usage and reboot as needed. |
3 | S-Cz8.1.0m1 | S-Cz8.1.0m1p18b |
30498837 | A sipd process crash occurs with
a signature containing the following:
The SBC can leak File Descriptors in cases where
there are certain process errors. For example:
This does not trigger proper closure of sockets. This is avoided by closing the socket that was opened and then setting an error identifying exact error code. |
2 | S-Cz8.1.0m1p18 | S-Cz8.1.0m1p18b |
29403076 |
The "thread-event" and "thread-usage" HDR categories are displaying incorrectly due to MBCD and SIPD thread names not properly writing into the files and OID output. MBCD and SIPD now properly assign and pass the proper names. |
3 | S-Cz8.1.0m1p9 | S-Cz8.1.0m1p18b |
29633588 |
During certain configuration activities, the SBC restarts due to an issue caused by improper configuration steps being processed in the sip-manipulation, header-rules. The SBC now returns an error message stating "Invalid Selection" instead of failing. |
3 | S-Cz8.1.0m1p11 | S-Cz8.1.0m1p18b |
29937232 |
GW unreachable and NetBufCtrl MBUFF errors - This can result in system instability including crash, gw-unreachable and redundancy issues. System will switchover if in HA. Show Buffers output will normally show an increase of errors reported in the NetBufCtrl field due to mbuf’s not being freed. |
2 | S-Cz8.3.0 | S-Cz8.3.0p6 |
288.2.0258 | On VNF platforms, when running
TLS Chat on VMware-PV 4core (SSFD) + 16GB, TLS Chat sessions are
gradually decreasing. When looking in Wireshark at EXFO, EXFO
forwards a wrong TLS MSRP Chat payload to EXFO UAS.
TCP Chat does not have this error. |
3 | S-Cz8.0.0 | S-Cz8.3.0m1p2 |
For Advanced Media Termination deployments using the 4600, 6300, 6350 platforms, the SBC is generating RTP and RTCP on the ports 20000 and 20001, instead of generating both on the same port 20000. | 3 | S-Cz8.3.0 | S-Cz8.3.0m1p2 | |
29522609 | Some calls that are configured to generate ring back tones result in one-way audio. | 2 | S-Cz8.3.0 | S-Cz8.3.0m1p2 |
29558827 | IMS-AKA calls running over IPv6 networks which utilize VLANs on systems with Mellanox network interfaces may experience one-way audio. | 3 | S-Cz8.3.0p3 | S-Cz8.3.0m1p2 |
29580506 | SBCs running on virtual platforms or the Acme Packet 3900 could switch over when running IMS-AKA calls involving refresh registrations. | 2 | S-Cz8.3.0p3 | S-Cz8.3.0m1p2 |
29607573 | The SBC is unable to successfully initiate a TCP connection to configured Diameter Accounting (Rf) servers. | 2 | S-Cz8.3.0 | S-Cz8.3.0m1p2 |
30114764 |
When presenting the content type for SPIROU during SIP to SIPI interworking, the SBC is displaying the text base=spirou. Based on relevant standards, it should display base=itu-92+ as the content type. | 4 | S-CZ8.3.0m1 | S-Cz8.3.0m1p2 |
30127762 |
When performing SIP to SIPI interworking, the SBC is not including an ISUP REL in the interworked body of its 400 Missing CSeq message when it rejects applicable calls from the SIPI side. | 4 | S-CZ8.3.0m1 | S-Cz8.3.0m1p2 |
30240798 |
The OCSBC closes connections when using some SFTP clients, including WinSCP and MOBA, to upload files over 200KB. Workaround - Use the Linux or Filezilla SFTP client when uploading files greater than 200k. |
3 | S-CZ8.3.0p6 | S-Cz8.3.0m1p2 |
30289027 |
Azure does not always properly
reset media interfaces after the OCSBC reboots. Instead, Azure
sometimes tries to process a non-existent packet as soon as the
OCSBC comes back up, resulting in a kernel panic.
Workaround - If you experience a kernel panic after OCSBC reboot, stop and restart the vSBC from the Azure UI. |
3 | S-Cz8.3.0 | S-Cz8.3.0m1p2 |
30453532 |
The Web GUI available in the S-Cz8.3.0M1 release cannot adequately be used to configure the Enterprise SBC. Workaround: For Web GUI support, use releases either prior to S-Cz8.3.0M1, or releases S-Cz8.3.M1p2 and later. |
2 | S-Cz8.3.0m1 | S-Cz8.3.0m1p2 |
26258705 |
The show sipd srvcc command does not display the correct number of unsuccessful aSRVCC calls. | 3 | S-Cz8.0.0 | S-Cz8.3.0 |
28617938 |
The anonymize-invite option for CommMonitor is not
RTC. To see a change, you must either reboot or toggle the admin
state. The following is a general admin state toggle procedure:
|
4 | CZ8.1.0m1 | S-Cz8.3.0 |
29556215 | The SBC does not send SIPREC data to a remote call server. | 2 | S-Cz8.3.0 | S-Cz8.3.0p5 |
29608499 | In all documents except for the Release Notes and Installation guide, the printed version of this release (S-Cz8.3.0) is incorrectly displayed as S-Cz8.2.0. | 4 | S-Cz8.3.0 | S-Cz8.3.0p3 |
28539155 | When operating as a VNF and using Mellanox interface cards, the OCSBC does not support ICMP over IPv6. | 3 | S-Cz8.2.0 | S-Cz8.3.0 |
29322490 | The SBC intermittently does not process the registration (Event: reg) of a SUBSCRIBE with Expires header=0 that should be created after receiving a NOTIFY with a termination request from a UE. | 2 | S-Cz8.2.0 | S-Cz8.3.0 |
28526228 | Maximum SRTP capacity on VNF platforms is 25% lower than in the S-Cz8.1.0 release. Expected capacity will be restored in a follow up patch. | 3 | S-Cz8.2.0 | S-Cz8.3.0 |
28679339 |
When supporting SRVCC roaming calls, the OCSBC is handling SRVCC end-station de-registration events by properly including associated URIs in the 200 OK. It is not, however, saving those associated URIs in its registration cache. This causes the OCSBC to respond to calls to those URIs with 404 not found messages until the end-station re-registers. | 2 | S-Cz8.0.0 | S-Cz8.3.0 |
26313330 |
In some early media call flows, the SBC may not present the correct address for RTP causing the call to terminate. | 3 | S-Cz8.0.0 | S-Cz8.2.0 |
26281599 |
The system feature provided by
the phy-interfaces
overload-protection parameter and overload-alarm-threshold sub-element is not
functional. Specifically, enabling the protection and setting
the thresholds does not result in trap and trap-clear events
based on the interface's traffic load.
The applicable ap-smgmt.mib SNMP objects include:
|
3 | S-Cz720 | S-Cz8.2.0 |
25144010 |
When an SBC operating on an Acme Packet 6300 switches over, the secondary can successfully add new ACL entries, but it also retains old ACL entries that it should have deleted. | 3 | S-Cz7.4.0p1 |
S-Cz8.2.0 |
26183767 |
When operating in HA mode and handling large traffic loads, the active SBC stops responding when you restore large configurations that are different from the configuration the active is currently running. The system subsequently goes out of service. | 3 | S-Cz8.0.0 |
S-Cz8.2.0 |
21975038 | The Acme Packet 4600, 6100, 6300, and 6350 platforms do not support MSRP File Transfer. | 3 | S-Cz8.1.0 | S-Cz8.2.0 |
27539750 |
When trying to establish a connection between the SBC and your network, while using TLS version 1.2, the SBC may reject the connection. Workaround: You may need to adjust your cipher list. |
3 | S-Cz8.1.0 | S-Cz8.1.0 |
28062411 | Calls that require SIP/PRACK interworking as invoked by the 100rel-interworking option on a SIP interface do not work in pooled transcoding architectures. | 2 | S-Cz7.4.0 | S-Cz8.2.0 |
28071326 | Calls that require LMSD interworking, as invoked by the lmsd-interworking option on a SIP interface, do not work in pooled transcoding architectures. During call establishment, when sending the 200 OK back to the original caller, the cached SDP is not included. | 2 | S-Cz7.4.0 | S-Cz8.2.0 |
None | The CZ8.1.0 release does not
support IPSec on the Acme Packet 3900 and VNF. You must upgrade
to CZ8.1.0p1 to get this support. After you upgrade to
CZ8.1.0p1, do the following:
|
N/A | S-Cz8.1.0 | S-Cz8.2.0 |
28.3.05575 | On VNFs, the system erroneously displays the IPSEC entitlement under "Keyed (Licensed) Entitlements." The error does not affect any functionality and you do not need to do anything. | 4 | S-Cz8.1.0 | S-Cz8.2.0 |
28659469 |
When booting CZ8.1.0M1 on any
virtual platform, not all system processes start. This known
issue only occurs on initial boot, and not in an upgrade
scenario.
Workaround: Reboot the SBC a second time, after it initially starts. |
3 | SCz8.1.0m1 | S-Cz8.2.0 |
If you configured the ims_aka option, you must also configure sip-interfaces with an ims-aka-profile entry. | 3 | E-Cz7.4.0 | E-Cz7.4.0m1 | |
27811129 |
When upgrading an OCSBC from a version that uses License Keys to enable CODECs, you must reboot the system after setting any CODEC entitlements to override the License Keys. | 3 | S-Cz8.1.0 | S-Cz8.3.0 |
30152019 |
Oracle has identified a Potential tSipd crash when configured for a VOLTE w/SRVCC scenario. When the issue is encountered, there is a sipd crash and, if configured, an HA switchover. This is a race condition that is relatively rare, but has been seen in internal testing. System Impact of HA Switchover:
|
3 | S-Cz8.3.0p7 | S-Cz8.3.0m1 |
28610095 |
In some circumstances, and with add-sdp-invite and add-sdp-profile configured, the SBC does not include the original SDP in a Re-INVITE that has no SDP. This does not comply with RFC 3264. Instead, the SBC inserts the negotiated media information from the last successful negotiation as the ReINVITE's SDP offer and sends this ReINVITE with inserted SDP to the next hop signaling entity. This issue is evident by the contents of the SDP o line. | 3 | S-Cz7.4.0 | S-Cz8.3.0m1 |
29541242 | Installation and Platform Preparation guide incorrectly includes information about setting up HA on Oracle Cloud platforms. These platforms do not support HA deployments at this time. | 3 | S-Cz8.3.0 | S-Cz8.3.0m1 |
34233796 | T.38 transcoding is not available on the Acme Packet 3950 and Acme Packet 4900 platforms. | 2 | S-Cz9.0.0 | S-Cz9.0.0p5 |
ID | Description |
---|---|
30612465 |
On Virtual platforms, the OCSBC is not forwarding traffic transcoded to EVS or Opus codecs if you have configured the applicable policy with a forced ptime of 60ms. |
25954122 |
Telephony fraud protection does not black list calls after a switchover. Workaround: Activate the fraud protection table on the newly active server. |
31162394 | Running SIPREC on the Acme Packet
4600 over 1G interfaces may result in system instability.
Workaround : Do not egress traffic out of a physical interface that exceeds the bandwidth of the physical media capacity. You should determine the amount of egress media traffic and the amount of intercepted traffic on that interface. The intercepted traffic could be any recorded traffic on the interface like (SIPREC, LI, and remote packet trace). |
26598075 |
When running on the Acme Packet 4600, the OCSBC sends a 200OK with IPv4 media address for call flows with offerless INVITES and the OCSBC configured with add-sdp-invite=invite and ALTC configured for IPv6 on the egress. |
26559988 |
In call flows that include dual ALTC INVITEs from the callee, and subsequent Re-INVITEs that offer an ALTC with IPv6 video, the OCSBC may not include the m lines in the SDP presented to the end stations during the Re-INVITE sequence. This results in the call continuing to support audio, but not video. |
26260953 |
Enabling and adding Comm Monitor
config for the first time can create a situation where the
monitoring traffic (IPFIX packets) does not reach the Enterprise
Operations Monitor.
Workaround: Reboot the system. |
28748784 | When operating as a VNF and using Mellanox interface cards, the OCSBC does not support outbound ICMP. |
30794993 |
The SBC might display an excessive number of debug messages after an HA switchover, if you configured both X123 LI and IKEv2/IPSec with IPv6 security policies. |
23756306 |
When you configure the session-router with an operation-mode of session, it does not correctly clear sessions. |
21805139 |
RADIUS stop records for IWF calls may display inaccurate values. |
26136553 |
The SBC can incur a system-level service impact while performing a switchover using "notify berpd force" with an LDAP configuration pointing to an unreachable LDAP server. Workaround: Ensure that the SBC can reach the LDAP server before performing switchover. |
28770472 | ACLI Users will receive an error on the output of the show registration sipd by-user command. |
29999832 and 30194470 |
When deployed as a vSBC, configured for IMS-AKA, and operating with registrations exceeding 60k, the OCSBC may exhibit performance degradation, exhibited by high CPU load or system crash. Workaround - Oracle has found that disabling the security-policy sa-lookup-exception parameter allows IMS-AKA to function correctly while supporting a high number of registrations. This parameter is enabled by default. Disable this parameter within all applicable security policies before running IMS-AKA. This parameter, when enabled on Acme Packet hardware, works as designed. |
32062551 | Virtual SBC platforms may incorrectly assess link status thereby causing major health degradation and triggering a failover. |
30595413 | The IKEv2/IPSEC negotiation fails while using TRANSPORT MODE and different IP’s for IKE and SIP interfaces. |
23253731 |
After an HA switchover, the new standby SBC retains some IMS-AKA subscriber TCP sockets. You can clear these sockets by rebooting the SBC. |
29005944 | On Acme Packet hardware in an HA configuration, with a large number of IMS-AKA endpoints, the standby is unable to synchronize, and when rebooted goes OOS. |
27031344 |
When configured to perform SRTP-RTP interworking, the SBC might forward SRTP information in the SDP body of packets on the core side, causing the calls to terminate. Workaround: Add an appropriately configured media-sec-policy on the RTP side of the call flow. This policy is in addition to the policy on the SRTP side of the call flow. |
30520181 |
When performing large numbers of simultaneous registrations, such as during a registration flood, the OCSBC may become unstable and stop responding when it exceeds 200k IMS-AKA subscriber registrations. |
ACMECSBC-23446
24809688 |
Media interfaces configured for IPv6, and using different VLANs that operate over different infrastructures, including VoLTE and 3GPP, are not supported. |
28639227 | When operating as a VNF and using Mellanox interface cards, the OCSBC does not support SCTP transport. |
28906914 | For transcoding use cases, the G711/G729 codec pair might experience unstable performance when each DSP has greater than 500 transcoding sessions. |
N/A | The T.140-Baudot Relay is not excluded from supported features with pooled transcoding. |
N/A | When operating as a VNF deployed in an HA configuration, the OCSBC does not support IPSec. |