ent-ee-flt

Use this command to enter Eagle Eyes Filter data in the Eagle Eyes Filter (EE FLT) table. The EE FLT entry consists of a Filter ID and Filter specific data. After the FLT ID is provisioned, it can be used in the dlt-ee-flt and chg-ee-card commands.

Parameters

type (mandatory)

Eagle Eyes Filter Type.

Range:: inc; exl

appl (mandatory)

Card Application Type

Range:: atm; ip; e1t1

ipprot (optional)

Filter based on IP sub-protocol

Range:: sctp; tcp; udp

ipsrc (optional)

Filter based on IP source address

Range:: 4 numbers separated by dots, with each number in the range of 0-255

ipdst (optional)

Filter based on IP destination address

Range:: 4 numbers separated by dots, with each number in the range of 0-255

ssport (optional)

Filter based on SCTP source port

Range:: 0-65535

sdport (optional)

Filter based on SCTP destination port.

Range:: 0-65535

stype (optional)

Filter based on SCTP chunk type

Range:: abrt; data; err; hbak; htbt; inak; init; sack

sctppld (optional)

Filter based on SCTP data payload identifier.

Range:: diam; m2pa; m3ua; sua; unspec

sctpstr (optional)

Filter based on SCTP data stream identifier

Range:: 0-65535

sscopsu (optional)

Filter based on SSCOP sub-protocol or SU type.

Range:: all; ctrl; data

mtp3si (optional)

Filter MTP3 user.

Range:: bicc; isup; sccp; snm; tup

port (optional)

Filter based on port.

Range:: a-b; a1-a31; b1-b31; all

sutype (optional)

Filter based on SU type.

Range:: allsu; lsu; msu

Example

ent-ee-flt:appl=ip:type=inc:ipprot=sctp:ssport=2048:stype=data:sctpstr=100

ent-ee-flt:appl=atm:type=exl:port=a:sscopsu=data:mtp3si=sccp

ent-ee-flt:appl=e1t1:type=exl:port=a1:sutype=msu:mtp3si=tup

Dependencies

If the appl=ip then ipprot, ipsrc or ipdst parameters must be specified.

If the ssport, sdport or stype parameters are specified, then the ipprot=sctp parameter must be specified.

At least one optional parameter (ipprot or port) must be specified.

If the sctppld parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.

If the sctpstr parameter is specified, then the stype=data and ipprot=sctp parameters must be specified.

The Eagle Eyes Filter table cannot contain more than 200 entries.

The Eagle Eyes Filter table must be available.

If the appl=ip parameter is specified, then the appl=atm and appl=e1t1 parameters must not be specified.

If the appl=atm parameter is specified, then the appl=ip and appl=e1t1 parameters must not be specified.

If the appl=e1t1 parameter is specified, then the appl=atm and appl=ip parameters must not be specified.

If the appl=atm parameter is specified, then the port parameter can only be either a, b or a1.

Notes

IP7 parameters:

ipprot, ipsrc, ipdst, ssport, sdport, style, sctppld, sctpstr

ATM parameters:

sscopsu, mtp3si, port

E1T1 parameters:

sutype, mtp3si, port

Output

ent-ee-flt:appl=atm:type=inc:port=a:sscopsu=data


    tekelecstp 10-03-08 14:43:31 EST  EAGLE 46.0.0
    EE FLT table is (1 of 200) 1% full
    ENT-EE-FLT: MASP A - COMPLTD 
;