6.8 msucount

This command is used to report the count of SS7 MSUs and bytes that pass through links, routing keys, and IP connections. These counts can be reported and reset at the same time to get accurate counts for longer periods of time. In addition to MSUs transmitted and received, the command also reports statistics on packets related to MTP Primitives and on discarded transmit and receive data.

Options

Options and option parameters that are underlined indicate that a value must be specified for that option or parameter. For example, the msucount command option -l has the parameterport. The link for which counts will be displayed can be specified, as in the command msucount -l a1. Do not enter the underlined option or parameter; enter a value for the information represented by the underlined option or parameter.

-a

This option is used to display IP connection statistics for a specific association. When -a aname is specified on the same line as -k rtkey, the output is assumed to be routing key output. When -a aname is specified on the command line without -k rtkey, association statistics output is generated.

For IPSG cards, this option is enhanced to include receive and transmit counts for M3UA SSNMs (DAUD messages and M3UA SSNM PDUs) and replicated M3UA PDUs.

-b

This option is used to display signaling link bytes statistics. The signaling link bytes report displays data for measurements on a per-signaling-link basis for both the transmit and receive directions. The report can display link statistics for a specified signaling link number. If a link is not specified, the report displays link statistics for signaling link A for IPGWx cards and for all equipped signaling links for IPLIMx and IPSG cards. If a signaling link is valid for the card and application type, but is unequipped, then the report displays all zeros.

-h

This option is used to provide help information for the command.

-f

This option is used to display a full report (IPGWx application only).

-k rtkey

This option is used to specify the routing key for which the counts will be displayed. The routing key is specified as a single parameter with up to five colon-separated fields. The subsystem is not specified when SI is not equal to 3.

This option is not supported for the IPSG cards.

The -p modifier can be specified to identify the point code type of the routing key that follows the -k option in the command.

The -p modifier is not supported for IPLIMx and IPSG cards.

The rtkey variable is optional when used with -t default, and mandatory for all other cases.

The following formats are valid for the routing key that follows the -k option in the command:

  • n-c-m:s:n-For DPC, SI, SSN type routing keys. The network, cluster and member (n-c-m) are in the range 0-255. The service indicator (s) is 3 or sccp. The subsystem (n) is in the range 0-255.
  • n-c-m:s-For DPC, SI, type routing keys. The network, cluster and member (n-c-m) are in the range 0-255. The service indicator (s) is in the range 0-2, 4, or 6-15. There is no subsystem. As a default, counts for all routing keys within the option combination are displayed.
  • n-c-m:s:no-co-mo:cs:ce-For DPC, SI, CIC type routing keys. The DPC network, cluster and member (n-c-m) are in the range 0-255. The service indicator (s) is 5 or isup. There is no subsystem. The OPC network, cluster and member (no-co-mo) are in the range 0-255. The starting circuit identification code (cs) and ending circuit identification code (ce) are in the range 0 to 16363.
-l

For IPSG cards, this option displays the link report for all equipped signaling links on the card.

-l link

This option is used to display counts for links. The link report optionally allows display of link statistics for a specified port.

The link report contains data, per link, for MSUs (tx/rcv), MSU bytes (tx/rcv), MGMT msgs (tx/rcv), and discarded data (tx/rcv).

For the IPSG card, the M2PA link report is the same as the IPLIMx M2PA report. The M3UA link report contains an additional detail line for non-discard pegs for SS7 SNM and Replicated M3UA PDU counts.

Range:
a, b, a1, b1, a2, b2, a3, b3a:a63-b:b63

If a port is not specified, msucount displays link statistics for port a for IPGWx links, and port a and port b for IPLIMx links.

The msucount link statistics report contains all zeros for a port that is valid for the card and application type but is unequipped.

The range a:a15-b:b15 is valid for IPSG ENET cards.

The range a:a63-b:b63 is valid for IPSG ENET cards.

-l

link -f

This option displays the full link report. For IPSG-M2PA links, this option displays the same report as the -l <link> option. For IPSG-M3UA links the report includes the data from the -l <link> report and includes an additional detail line displaying tx/rx discards counts and discard data.

-p point code type

This option modifier can be specified along with the -k option to identify the point code type (ANSI, ITU international, ITU-national, 24-bit ITU national, 16-bit ITU national, ITU international spare, and ITU national spare) in the routing key that follows the -k option in the command.

Range:
ansi, itui, itun, itun24, itun16, ituis, ituns
-r

This option is used with other options to reset counts at the same time of reporting them.

-t keytype

This option is used to display the routing key type (IPGWx only).

-x

The routing context is an index that uniquely defines a routing key associated with an SUA or M3UA AS. For the IPSG card, the option displays a link report for all signaling links on the card that are members of the linkset that contains the specified routing context value (equivalent to the msucount -l report. The -x option is used as an alternative to the -k option to identify the routing key by specifying its routing context in the command line.

Note:

The -x rc option can only be used to specify routing keys containing M3UA/SUA associations.

Example

Link counts only. Displays brief count for signaling link a for IPGWx. Displays counts for all equipped signaling links for IPLIMx.

msucount -l

Link counts only, for signaling link port a1.

msucount -l a1

Full/detail report for signaling link a for IPGWx.

msucount -l -f

Counts for the specified association only.

msucount -a association name

Counts for first matching routing key

msucount -k 10-10-10:3:16

Counts for the routing key report using the routing context.

msucount -x 5

Counts for first matching routing key and an associated association.

msucount -a association name -k rtkey

Counts for the default routing key

msucount -k -t default

Counts for a matching partial routing key.

msucount -k 3-3-3 -t partial

Counts for counts for link only. Displays brief report for signaling link a for IPGWx. Displays counts for all equipped signaling links for IPLIMx.

msucount

Resets the signaling link count measurements.

msucount -r

Brief version of help text.

msucount -h

Full version of help text.

msucount -h full

Counts for link and first matching routing key

msucount -b

Byte report for signaling link A for IPGWx cards. Byte report for all equipped signaling links for IPLIMx cards.

msucount -b -link

Byte report for specified signaling link.

msucount -l -k 10-10-10:3:16

Use with other parameters to display and reset counts. Valid with the above combinations.

msucount -l -r

msucount -r

msucount -x 5 -r

Examples showing the correct syntax to specify partial or default keys, or to specify a key by routing context:

pass:loc=1105:cmd="msucount -k 5-5-1:5:6-6-6 -t partial

pass:loc=1105:cmd="msucount -k 5-5-1:5 -t partial"

pass:loc=1105:cmd="msucount -p ITUI -t partial -k 1-235-1"

pass:loc=1105:cmd="msucount -p ITUN -t partial -k 2351"

pass:loc=1105:cmd="msucount -p ITUN -t partial -k 2351-gr

pass:loc=1105:cmd="msucount -t partial -k :2 "

pass:loc=1105:cmd="msucount -k -t default"

pass:loc=1105:cmd="msucount -p ITUN24 -t partial -k 10-235-1"

pass:loc=1105:cmd="msucount -p ITUN24 -t partial -k 10-235-1"

pass:loc=1105:cmd="msucount -p ITUN16 -t partial -k 1-2-1"

Examples of other valid routing key inputs:

pass:loc=1105:cmd="msucount -r -k 5-5-6:5:5-5-7:1:1000"

pass:loc=1105:cmd="msucount -r -p ITUI -k 5-5-6:4:5-5-7:1:1000"

pass:loc=1105:cmd="msucount -k 5-5-1:3:5 -a assoc1"

pass:loc=1105:cmd="msucount -r -p ITUN24 -k 15-105-16:5:15-105-17:1:1000"

Dependencies

At least one option must be specified.

Notes

The msucount command is executed through the pass command.

Combinations of the -l, -a, -k, -t, -x and -b options provide count information based on the entered combination.

If no parameters are specified, then the -l brief report is output.

Multiple reports are not supported with the IP Signaling Serviceability feature.

For the SS7IPGW and IPGWI GPLs, 4 types of reports can be generated: the link report, the routing key report, the IP connection statistics report, and the signaling link bytes report. For the IPLIMI card, the routing key report is not supported.

The 4 reports are:
  1. The link report (-l option) contains statistics per link about MSUs (transmit/receive), MSU bytes (transmit/receive), MGMT messages (transmit/receive), and discarded data (transmit/receive).
  2. The routing key report (-k option) contains statistics for a specific routing key about MSUs (transmit), MSU bytes (transmit), and discards on the transmit path for the routing key.

    A list of one or more IP connections associated with the routing key, with the MSU and MSU bytes counts for each connection, is also displayed. If -aaname is in the same input command with -krtkey, only the connection association data for the specified connection is displayed. If -a aname is not specified with -k rtkey, all connection associations are listed. If -x rc is specified, only the connection association data for the specified routing context is displayed.

    The -p (point code type) modifier option can be used with the -k option to specify the point code type of the routing key that follows the -k option in the command.

    For the -k options, the routing key must be an exact match of a routing key that exists in the static Routing Key table.

  3. The IP connection statistic report (-a aname option) contains statistics for a specified IP connection about MSUs (transmit/receive), MSU bytes (transmit/receive), and discarded data (transmit/receive).

    When the -a aname option is specified in the command with the -k option, the output type is assumed to be routing key output.

    When the -a aname option is specified in the command without the -k option, association statistics output is generated.

  4. The signaling link bytes report (-b option) provides the following information for both IPGWx and IPLIMx cards: bytes/sec for the last second, average MSU size during the last second, and maximum one-second average MSU size since card load time or reset. For the IPLIMx cards, the report also provides the following information: sum of bytes/sec for the last second for all signaling link, average MSU size for last second for all signaling links, maximum average MSU size since load time or reset for all signaling links, and maximum MSU size since load time or reset for all signaling links.

The link report, routing key report, and IP connection statistics report (IPGWx only) can display individual transmit MSUs that were discarded at layer 2. The first 32 bytes of the MSU transmit data that is discarded is stored beginning at the SIO bytes. If the MSU is not 32 bytes long, the remaining bytes are set to 0.

The signaling link bytes report optionally allows display of link statistics for a specified signaling link number. If a link is not specified for the bytes report, the msucount command displays link statistics for signaling link A for IPGWx cards and for all equipped signaling links for IPLIMx cards.

The signaling link bytes report contains all zeros for a signaling link that is valid for the card and application type but that is unequipped.

The link and IP connection statistics reports can display individual receive packets that were discarded at layer 2. If the storage space is larger than the service data, the extra bytes are set to 0.

The reset option (-r) resets the specified measurements. This option can be added to any command.

Output

In these examples, the hexadecimal output for discarded transmit data represents data stored beginning at the SIO bytes through the first 32 bytes of the MSU. If the MSU was less than 32 bytes, the remaining bytes are represented by zeros.

Stored receive data takes the following format:
  • Bytes 13-x = Service data. If the storage space is greater than the size of the service data, the remaining bytes are zeroed.

Output Specific to SS7IPGW and IPGWI

Either brief or full help reports can be displayed. A full help report is generated by adding the full (-f) option to the command line.

This example shows a brief help report:

pass:loc=1105:cmd="msucount -h"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    Usage: msucount [ [-l [link]] | [-b [link]] ] |
                    [ [-a aname] ] |
                    [ [-x rc] | [-k [rtkey] [-p pctype] [-t keytype]] ]
                    [-f] [-r] [-h [full]]

    Options: -l  display signaling link report
             -b  display signaling link bytes report
             -a  display association report
             -x  routing key report using routing context
             -k  routing key report using MTP3 parameters
                 rtkey :: ([dpc][:si][:opc | :ssn][:cics][:cice])
             -p  pctype :: (ANSI, ITUI, ITUN, ITUN24, ITUN16, ITUIS, ITUNS)
             -t  routing key type
                 keytype :: (<full>, partial, default)            
             -f  display full report
             -r  resets the specified counts
             -h  display command help (brief or full)

    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0
    MSUCOUNT command complete

;

This example shows a full help report:

pass:loc=1105:cmd="msucount -h full"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    Usage: msucount [ [-l [link]] | [-b [link]] ] |
                    [ [-a aname] ] |
                    [ [-x rc] | [-k [rtkey] [-p pctype] [-t keytype]] ]
                    [-f] [-r] [-h [full]]
 
    Options: -l  display signaling link report
             -b  display signaling link bytes report
             -a  display association report
             -x  routing key report using routing context
             -k  routing key report using MTP3 parameters
                 rtkey :: ([dpc][:si][:opc | :ssn][:cics][:cice])
             -p  pctype :: (ANSI, ITUI, ITUN, ITUN24, ITUN16, ITUIS, ITUNS)
             -t  routing key type
                 keytype :: (<full>, partial, default)            
             -f  display full report
             -r  resets the specified counts
             -h  display command help (brief or full)

 
    -k option details:
 
        Use the -p option along with -k to specify the SS7 network
        domain and point code format for the network. The SS7IPGW
        default pctype is ANSI. The IPGWI default pctype is ITUI.

            Network  PC Format Notes
            -------  --------- --------------------------------------
            ANSI     N-C-M
            ITUN     N         Non-Spare ITU National, no group code
            ITUN     N-GC      Non-Spare ITU National with group code
            ITUI     Z-A-I     Non-Spare ITU International
            ITUN24   N-C-M     Non-Spare ITU National, 24-bits
            ITUN16   U-S-M     Non-Spare ITU National, 16-bits
            ITUNS    N         Spare ITU National, no group code
            ITUNS    N-GC      Spare ITU National with group code
            ITUIS    Z-A-I     Spare ITU International
             
        Use the -t option along with -k to specify certain MTP3 and
        user part MSU fields as wildcards for the routing key.
 
        SS7 Traffic Partition              RTKEY Parameter Example
        ---------------------------------  ----------------------------
        Any User Part to DPC 1-1-1         -k 1-1-1    -t partial
        SCCP to DPC 1-1-1                  -k 1-1-1:3  -t partial
        ISUP to DPC 1-1-1                  -k 1-1-1:5  -t partial
        TUP to DPC 1-1-1                   -k 1-1-1:4  -t partial
        QBICC to DPC 1-1-1                 -k 1-1-1:13 -t partial
        SI [0-2,6-12,14,15] to DPC 1-1-1   -k 1-1-1:SI
        SCCP SSN 5 to DPC 1-1-1            -k 1-1-1:3:5
        ISUP to DPC 1-1-1 from OPC 2-2-2   -k 1-1-1:5:2-2-2  -t partial
        TUP to DPC 1-1-1 from OPC 2-2-2    -k 1-1-1:4:2-2-2  -t partial
        QBICC to DPC 1-1-1 from OPC 2-2-2  -k 1-1-1:13:2-2-2 -t partial
        ISUP CIC 1 to 1-1-1 from 2-2-2     -k 1-1-1:5:2-2-2:1
        TUP CIC 1 to 1-1-1 from 2-2-2      -k 1-1-1:4:2-2-2:1
        QBICC CIC 1 to 1-1-1 from 2-2-2    -k 1-1-1:13:2-2-2:1
        ISUP CIC 0-5 to 1-1-1 from 2-2-2   -k 1-1-1:5:2-2-2:0:5 
        TUP CIC 0-5 to 1-1-1 from 2-2-2    -k 1-1-1:4:2-2-2:0:5
        QBICC CIC 0-5 to 1-1-1 from 2-2-2  -k 1-1-1:13:2-2-2:0:5
        Default Routing Key                -k                 -t default

    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0
    MSUCOUNT command complete

A brief version for the link measurement report can be specified for IPGWx. If no parameters are specified for a link measurements report, then a brief report is displayed. The brief report does not display the transmit/receive discard counts.

This example shows a brief link measurements report:

pass:loc=1305:cmd="msucount"

or

pass:loc=1305:cmd="msucount -l"
    tekelecstp 10-08-17 11:50:34 EST  EAGLE 42.0.0

    MSUCOUNT: MSU Count Report

    --------------------------
    Link Measurements (Link A) 
    --------------------------

    Transmit Counts                      Receive Counts
    ----------------------------------   -----------------------------
    rate   msus        bytes             rate   msus        bytes
    -----  ----------  ---------------   -----  ----------  ----------
    2000   4294967295  4294967295        2000   4294967295  4294967295


    MTP Primitive (MTPP) counts          Reroute Counts             
    ----------------------------------   ----------------------     
    sent pdus   rcvd pdus   dscrd pdus   sent msus   rcvd msus        
    ----------  ----------  ----------   ----------  ----------     
    4294967295  4294967295  4294967295   4294967295  4294967295     


    MSUCOUNT: command complete
;

This example shows a full link measurements report:

pass:loc=1305:cmd="msucount -f"

or

pass:loc=1305:cmd="msucount -l -f"
    tekelecstp 10-08-17 11:50:34 EST  EAGLE 42.0.0


     MSUCOUNT: MSU Count Report

     --------------------------
     Link Measurements (Link A) 
     --------------------------

    Transmit Counts                      Receive Counts
    ----------------------------------   -----------------------------
    rate   msus        bytes             rate   msus        bytes
    -----  ----------  ---------------   -----  ----------  ----------
    2000   4294967295  4294967295        2000   4294967295  4294967295


    MTP Primitive (MTPP) Counts          Reroute Counts             
    ----------------------------------   -----------------------------     
    sent pdus   rcvd pdus   dscrd pdus   sent msus   rcvd msus        
    ----------  ----------  ----------   ----------  -----------------     
    4294967295  4294967295  4294967295   4294967295  4294967295     


    Transmit Discard Counts              Receive Discard Counts             
    ----------------------------------   --------------------------------           
    reason                 count         reason                 count      
    ---------------------- -----------   ---------------------- ---------- 
    no ss7 rtbl entry      4294967295    link state             4294967295
    no ss7 rtkey           4294967295    sccp msg type          4294967295
    no conn avail to pc    4294967295    sccp class             4294967295
    no conn avail to rtkey 4294967295    sccp called party      4294967295
    congested connection   4294967295    sccp calling party     4294967295
    sccp msg type          4294967295    isup sio               4294967295
    sccp class             4294967295    normalization error    4294967295
    circular rte           4294967295    error in XSRV packet   4294967295
    normalization error    4294967295    M3UA PDU error         4294967295
    invalid traffic type   4294967295    SUA PDU error          4294967295
    M3UA conversion error  4294967295    invalid rcontext       4294967295
    SUA conversion error   4294967295    management blocking    4294967295
    AS-Pending overflow    4294967295    lrg MSU not supported  4294967295
    AS timer Tr expiry     4294967295
    reroute failure        4294967295
    unexpected for APC     4294967295
    lrg MSU not supported  4294967295


    Stored Transmit Discard Data
    -----------------------------------------------
    83 01 05 05 0a 01 03 bf 09 80 03 08 0d 05 c3 07
    01 05 05 05 c3 07 0a 01 03 08 e2 06 c7 04 13 10


    Stored Receive Discard Data
    -----------------------------------------------
    53 41 53 49 73 63 63 70 1a 00 09 01 03 08 0d 05
    c3 05 0a 01 03 05 c3 05 01 05 05 08 e2 06 c7 04
    
    MSUCOUNT: command complete
    ;

This example shows an output report when all counts are zero:

pass:loc=1305:cmd="msucount -f"

or

pass:loc=1305:cmd="msucount -l -f"

    MSUCOUNT: MSU Count Report
    --------------------------
    Link Measurements (Link A) 
    --------------------------

    Transmit Counts                      Receive Counts
    ----------------------------------   -----------------------------
    rate   msus        bytes             rate   msus        bytes
    -----  ----------  ---------------   -----  ----------  ----------
    00000  00000       00000             00000  00000       00000  


    MTP Primitive (MTPP) Counts          Reroute Counts 
    ----------------------------------   -----------------------------
    sent pdus   rcvd pdus   dscrd pdus   sent msus   rcvd msus        
    ----------  ----------  ----------   ----------  -----------------     
    00000       00000       00000        00000       00000  


    Transmit Discard Counts              Receive Discard Counts 
    ----------------------------------   --------------------------------- 
    reason                 count         reason                 count      
    ---------------------- -----------   ---------------------- ---------- 
    no transmit discard counts           no receive discard counts


    Stored Transmit Discard Data
    -----------------------------------------------
    no stored transmit discard data


    Stored Receive Discard Data
    -----------------------------------------------
    no stored receive discard data
    
    MSUCOUNT: command complete

Routing Key Report Output Examples

The routing key report contains data about MSUs (tx), MSU bytes (tx), and discards on the transmit path for the routing key. A list of one or more connections associated with the routing key, with the MSU and MSU bytes counts for each connection, is also presented. If -a aname is in the same input command with -k rtkey, only the connection association data for the specified connection is displayed. If -a aname is not specified with -k rtkey, all connection associations are listed. If -x rc is specified, only the connection association data for the specified routing context is displayed.

Note:

For IPGWx, -k rtkey is optional when used with -t default, and mandatory for all other cases.

The report output itself does not display the routing key that was entered, other than an exact copy of the command line being generated as part of the output.

Partial routing keys (where some fields in the MSU are ignored with respect to finding a routing key to use for the MSU) and default keys can be specified in the command. The output does not change for these key types; the only difference is the routing key syntax (-p) that must be processed as part of identifying the partial and default keys. (See the Example section of this command description for syntax examples).

This example shows a routing key report for an ANSI routing key that specifies the Routing Key table:

pass:loc=1105:cmd="msucount -k 5-5-1:3: -t partial"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0
       
    MSUCOUNT: MSU Count Report

    ------------------------------------------------
    Routing Key Measurements for Static Routing Key
    ------------------------------------------------

    Transmit Counts
    --------------------
    tx bytes                                4294967295  
    tx msus                                 4294967295  

    Transmit Discard Counts
    -----------------------
    sccp msg type                           4294967295  
    sccp class                              4294967295  
    normalization error                     4294967295  
    invalid traffic type                    4294967295  

    Associated IP Connection                tx bytes        tx msus
    -----------------------------           --------        --------
    c7000                                   4294967295      4294967295  
    c7050                                   4294967295      4294967295  
    c7052                                   4294967295      4294967295  
    c7054                                   4294967295      4294967295  

    Stored Transmit Discard Data
    ----------------------------
    83 01 05 05 0a 01 03 94 09 01 03 08 0d 05 c3 05
    01 05 05 05 c3 05 0a 01 03 08 e2 06 c7 04 28 10


    MSUCOUNT: command complete

;

This example shows an ITU-I routing key report (only 1 specific association is displayed):

pass:loc=1105:cmd="msucount -p ITUI -k 5-5-1:3:5 -a c7000"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0
       
    MSUCOUNT: MSU Count Report

    ------------------------------------------------
    Routing Key Measurements for Static Routing Key
    ------------------------------------------------

    Transmit Counts
    --------------------
    tx bytes:                               4294967295  
    tx msus:                                4294967295  

    Transmit Discard Counts
    -----------------------
    sccp msg type                           4294967295  
    sccp class                              4294967295  
    normalization error                     4294967295  
    invalid traffic type                    4294967295  

    Associated IP Connection                tx bytes        tx msus
    -----------------------------           --------        --------
    c7000                                   4294967295      4294967295  

    Stored Transmit Discard Data
    -----------------------------------------------
    83 01 05 05 0a 01 03 94 09 01 03 08 0d 05 c3 05
    01 05 05 05 c3 05 0a 01 03 08 e2 06 c7 04 28 10


    MSUCOUNT: command complete
;

This example shows a routing key report when the routing context =5 (because a table is not specified, the key is searched for in the Static table):

pass:loc=1105:cmd="msucount -x 5"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    MSUCOUNT: MSU Count Report

    ------------------------------------------------
    Routing Key Measurements for Static Routing Key
    ------------------------------------------------

    Transmit Counts
    --------------------
    tx bytes                                4294967295  
    tx msus                                 4294967295  

    Transmit Discard Counts
    -----------------------
    sccp msg type                           4294967295  
    sccp class                              4294967295  
    normalization error                     4294967295  
    invalid traffic type                    4294967295  

    Associated IP Connection                tx bytes        tx msus
    -----------------------------           --------        --------
    c7000                                   4294967295      4294967295  
    c7050                                   4294967295      4294967295  
    c7052                                   4294967295      4294967295  
    c7054                                   4294967295      4294967295  

    Stored Transmit Discard Data
    -----------------------------------------------
    83 01 05 05 0a 01 03 94 09 01 03 08 0d 05 c3 05
    01 05 05 05 c3 05 0a 01 03 08 e2 06 c7 04 28 10


    MSUCOUNT: command complete

IP Connection Report

This example shows an IP Connection report for an association:

pass:loc=1105:cmd="msucount -a c7050"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    MSUCOUNT: MSU Count Report
    --------------------------
    IP Connection Measurements
    --------------------------

    Receive Counts                     Transmit Counts
    --------------------------------   -----------------------------
    msus            bytes              msus             bytes
    ----------      ----------------   ----------       ----------
    4294967295      4294967295         4294967295       4294967295

    Receive Discard Counts             Transmit Discard Counts             
    --------------------------------   ---------------------------------           
    reason                count        reason                 count      
    --------------------- ---------    ---------------------- ----------
    link state            4294967295   sccp msg type          4294967295  
    sccp msg type         4294967295   sccp class             4294967295  
    sccp class            4294967295   normalization error    4294967295  
    sccp called party     4294967295   invalid traffic type   4294967295  
    sccp calling party    4294967295   M3UA conversion error  4294967295  
    isup sio              4294967295   SUA conversion error   4294967295  
    normalization error   4294967295   management blocking    4294967295  
    error in XSRV packet  4294967295   transmit queue full    4294967295
    M3UA PDU error        4294967295  
    SUA PDU error         4294967295  
    invalid rcontext      4294967295  

    Stored Transmit Discard Data
    ----------------------------
    no stored transmit discard data

    Stored Receive Discard Data
    ---------------------------
    53 41 53 49 69 73 6f 74 11 00 87 0a 01 03 01 05
    05 00 01 02 03 04 05 06 07 08 09 00 00 00 00 00

    MSUCOUNT: command complete

;

The transmit queue full reason under Transmit Discard Counts section of this report refers to the count of the messages which are discarded due to connection manager transmit queue full. This count is incremented only for M3UA messages which are discardable.

Signaling Link Bytes Report

This example shows a signaling link bytes report for an IPGWx card:

pass:loc=1305:cmd=msucount -b"

or

pass:loc=1305:cmd=msucount -b a
    MSUCOUNT: MSU Count Report

    --------------------------------
    Link Byte Measurements (Link A)
    --------------------------------

    SLK Transmit counts               SLK Receive counts
    --------------------------------  --------------------------------
    bytes/     avg    max      max    bytes/     avg    max      max
    sec        msu    avg msu  msu    sec        msu    avg msu  msu
    ---------  -----  -------  -----  ---------  -----  -------  -----
    444400     2020   2020     2020   444400     2020   2020     2020


    MSUCOUNT: command complete

Output Specific to IPLIMI

Note:

The routing key report is not supported for IPLIMx applications. The -k, -t, -p, -x options are not supported because the IPLIMx card does not use routing keys.

Note:

The IPLIMx reports include all equipped signaling links instead of just ports A and B. These reports include the transmit/receive counts alongside each other for the link case.

This example shows help for using the command:

pass:loc=1103:cmd="msucount -h" or

pass:loc=1103:cmd="msucount"

    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    Usage: msucount [ [-l [link]] | [-b [link]] ] |
                    [ [-a aname] ]
                    [-r] [-h]
 
    Options: -l  display signaling link report
             -b  display signaling link bytes report
             -a  display association report
             -r  resets the specified counts
             -h  display command help

    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0
    MSUCOUNT command complete

;

This example shows a link report for an IPLIMx card with 2 M2PA links.

The report does not contain MTPP or RKRP MGMT statistics, because those capabilities are not supported on the IPLIMx applications. The report also does not contain tx/rcv discard data, because there are no discards performed at layer 2 of the IPLIMx applications. The IPLIMx card can also contain 2 links per card; the output contains link data for each link.

pass:loc=1301:cmd="msucount"

or

pass:loc=1301:cmd="msucount -l"
    MSUCOUNT: Command In Progress

    ;
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    2000   4294967295  4294967295   2000   4294967295  4294967295
    B    2000   4294967295  4294967295   2000   4294967295  4294967295
    A1   2000   4294967295  4294967295   2000   4294967295  4294967295
    B1   2000   4294967295  4294967295   2000   4294967295  4294967295
    A2   0000   0000000000  0000000000   0000   0000000000  0000000000 
        
    MSUCOUNT: command complete

This example shows signaling link A1 on an IPLIMx card:

pass:loc=1103:cmd="msucount -l a1"
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A1   2000   4294967295  4294967295   2000   4294967295  4294967295
    ; 
    MSUCOUNT: command complete

This example shows an IP connection statistics report. The IPLIMx IP connection report does not contain tx/rcv discard data, because there are no discards performed at layer 2 of the IPLIMx applications.

pass:loc=1105:cmd="msucount -a c7050"
    tekelecstp 10-09-10 11:50:34 EST  EAGLE 43.0.0

    MSUCOUNT: MSU Count Report
    --------------------------
    IP Connection Measurements
    --------------------------

    Transmit Counts                    Receive Counts
    --------------------------------   -----------------------------
    msus            bytes              msus             bytes
    ----------      ----------------   ----------       ----------
    4294967295      4294967295         4294967295       4294967295

     MSUCOUNT: command complete

;

Signaling Link Bytes Report

This example shows a signaling link bytes report for an IPLIMx card:

pass:loc=1303:cmd="msucount -b"
    MSUCOUNT: SLK Bytes Report

    SLK Transmit                      SLK Receive
    -------------------------------   -------------------------------
                         max                                max       
                    avg  avg   max                     avg  avg  max  
    slk   bytes/sec msu  msu   msu     slk   bytes/sec msu  msu  msu  
    ----- --------- ---- ----- ----    ----- --------- ---- ---- ----
    A     35000     140  273   273     A     35000     140  273  273    
    B     35000     140  273   273     B     35000     140  273  273    
    A1    35000     140  578   578     A1    35000     140  578  578     
    B1    35000     140  273   273     B1    35000     140  273  273     
    A2    35000     140  140   140     A2    35000     140  140  140     
    B2    35000     140  169   169     B2    35000     140  169  169     
    A3    35000     2048 2048  2048    A3    35000     2048 2048 2048     
    B3    35000     140  166   166     B3    35000     140  166  166     
    ----- --------- ---- ----- ----    ----- --------- ---- ---- ---- 
          280000    140  2048  2048          280000    140  2048 2048

    MSUCOUNT: command complete     

This example shows a signaling link bytes report for a specified link on an IPLIMx card:

pass:loc=1303:cmd="msucount -b a"
    MSUCOUNT: SLK Bytes Report

    SLK Transmit                      SLK Receive
    -------------------------------   -------------------------------
                         max                                max       
                    avg  avg   max                     avg  avg  max  
    slk   bytes/sec msu  msu   msu     slk   bytes/sec msu  msu  msu  
    ----- --------- ---- ----- ----    ----- --------- ---- ---- ----
    A     35000     140  273   273     A     35000     140  273  273    

    MSUCOUNT: command complete

Enhanced Reset Option

The reset option resets the specified measurements without displaying msucount output. The default is to reset the link measurements report.

This example shows resetting link measurements:

pass:loc=1305:cmd="msucount -l -r"

or

pass:loc=1305:cmd="msucount -r"
    eagle10212 06-06-01 08:50:47 EST  EAGLE 35.0.0

    MSUCOUNT: MSU Count Report

    Link measurements have been reset.
 
    MSUCOUNT: command complete

This example shows resetting Routing Key measurements:

pass:loc=1305:cmd="msucount -x -5 -r"
    eagle10212 06-01-05 08:50:47 EST  EAGLE 35.0.0

    MSUCOUNT: MSU Count Report

    Routing Key measurements have been reset.
 
    MSUCOUNT: command complete 

Output specific to IPSG Cards

The option to display a full help report is not supported for IPSG cards.

pass:loc=1304:cmd="msucount -h
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0 

    Usage: msucount [ [-l [link]] | [-b [link]] | [-l link -f] ] |
                    [ [-a aname] ]
                    [ [-x rc] ]
                    [-r] [-h]

    Options: -l  display signaling link report
             -b  display signaling link bytes report
             -a  display association report
             -x  display routing context report
             -f  display full report
             -r  resets the specified counts
             -h  display command help

;

    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0 

    MSUCOUNT: command complete

For link reports on IPSG signaling links, if a specific link is not requested, then counts for all equipped signaling links on the card are displayed. The report includes counts for up to 32 links per card. The -l <link> report adds counts for Replicated M3UA PDU sent, Replicated M3UA PDU rcvd, and SS7 SNM Counts sent for M3UA links.

This example shows a brief measurements report:

pass:loc=1303:cmd="msucount -l"
tekelecstp 16-05-25 12:38:16 EST  EAGLE5 46.4.0.0.0-69.3.1     
    pass:loc=1303:cmd="msucount -l"

    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      3           72           0      0           0
    B    0      62          1916         0      62          1916
    A41  0      2           48           0      0           0
    A2   0      1           24           0      0           0
    A3   0      0           0            0      0           0
    A54  0      0           0            0      0           0

    ----------------------------------   -----------------------------
         0      68          2060         0      62          1916
    ----------------------------------   -----------------------------


    MSUCOUNT: command complete

This example shows a measurement report for an IPSG-M3UA signaling link:

pass:loc=1303:cmd="msucount -l a"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0 
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      3           72           0      0           0


    Replicated M3UA PDU counts           SS7 SNM counts
    --------------------------           ---------------
    sent        rcvd                     sent
    ----------  ----------               ----------
    0           0                        3

This example shows a measurement report for an IPSG-M2PA signaling link:

pass:loc=1303:cmd="msucount -l b"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0 
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    B    0      62          1916         0      62          1916


    MSUCOUNT: command complete

The msucount -l <link> -f report displays the same information as the brief report (msucount -l <link>) for IPSG-M2PA links. For IPSG-M3UA links, the msucount -l <link> -f report displays both the information from the brief report and the discarded tx due to M3UA Conversion Error, discarded rcv due to M3UA PDU Error, discarded rcv due to Management Blocking, and discarded rcv due to Lrg BICC not supported discard counts.

This example shows a full report for an IPSG-M3UA signaling link when discard counts are not received:

pass:loc=1303:cmd=msucount -l a -f
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report


    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      3           72           0      0           0


    Replicated M3UA PDU counts           SS7 SNM counts
    --------------------------           ---------------
    sent        rcvd                     sent
    ----------  ----------               ----------
    0           0                        3


    Transmit Discard Counts              Receive Discard Counts
    ----------------------------------   ---------------------------------
    reason                 count         reason                 count
    ---------------------- -----------   ---------------------- ----------
    M3UA conversion error  2             no receive discard counts


    Stored Transmit Discard Data
    -----------------------------------------------
    b0 04 04 04 00 d4 01 1b 61 00 00 bb a9 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    b0 04 04 04 00 d4 01 16 61 00 00 27 b8 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00



    Stored Receive Discard Data
    -----------------------------------------------
    no stored receive discard data



    MSUCOUNT: command complete

This example shows a full report for an IPSG-M3UA signaling link when discard counts are received:

pass:loc=1304:cmd="msucount -l a -f"
    Command Accepted - Processing

    rlghncxa03w 10-03-09 11:31:09 EST  EAGLE 42.0.0

    MSUCOUNT: MSU Count Report



    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      58          3380         0      5           292


    Replicated M3UA PDU counts           SS7 SNM counts
    --------------------------           ---------------
    sent        rcvd                     sent
    ----------  ----------               ----------
    1           1                        13


    Transmit Discard Counts              Receive Discard Counts
    ----------------------------------   ---------------------------------
    reason                 count         reason                 count
    ---------------------- -----------   ---------------------- ----------
    M3UA conversion error  3             M3UA PDU Error         1
                                         management blocking    1
                                         lrg MSU not supported  1


    Stored Transmit Discard Data
    -----------------------------------------------
    b0 04 04 04 00 6e 01 18 51 01 00 0f 49 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    80 04 04 04 00 d2 01 00 23 05 05 05 02 1f 61 02
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    80 04 04 04 00 d2 01 00 13 20 19 02 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00




    Stored Receive Discard Data
    -----------------------------------------------
    01 00 04 01 00 00 00 18 00 0b 00 08 02 00 00 00
    00 06 00 08 00 00 00 04 00 00 00 00 00 00 00 00

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04   
    02 10 00 2b 00 04 04 04 00 05 05 05 0d 02 00 96

    01 00 00 10 00 00 00 1c 00 0c 00 08 00 00 00 06
    00 07 00 0c 01 00 02 02 00 00 00 18 00 00 00 00

    MSUCOUNT: command complete

;

This example shows a link report for an IPSG-M2PA signaling link:

pass:loc=1303:cmd="msucount -l b"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    B    0      62          1916         0      62          1916


    MSUCOUNT: command complete

This example shows a full link report for an IPSG-M3UA link where discard counts are not received:

pass:loc=1303:cmd=msucount -l a -f
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report


    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      3           72           0      0           0


    Replicated M3UA PDU counts           SS7 SNM counts
    --------------------------           ---------------
    sent        rcvd                     sent
    ----------  ----------               ----------
    0           0                        3


    Transmit Discard Counts              Receive Discard Counts
    ----------------------------------   ---------------------------------
    reason                 count         reason                 count
    ---------------------- -----------   ---------------------- ----------
    M3UA conversion error  2             no receive discard counts


    Stored Transmit Discard Data
    -----------------------------------------------
    b0 04 04 04 00 d4 01 1b 61 00 00 bb a9 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    b0 04 04 04 00 d4 01 16 61 00 00 27 b8 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00



    Stored Receive Discard Data
    -----------------------------------------------
    no stored receive discard data



    MSUCOUNT: command complete

This example shows a full link report that contains discard counts for an IPSG-M3UA link:

pass:loc=1304:cmd="msucount -l a -f"
    Command Accepted - Processing

    rlghncxa03w 10-03-09 11:31:09 EST  EAGLE 42.0.0

    MSUCOUNT: MSU Count Report



    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      58          3380         0      5           292


    Replicated M3UA PDU counts           SS7 SNM counts
    --------------------------           ---------------
    sent        rcvd                     sent
    ----------  ----------               ----------
    1           1                        13


    Transmit Discard Counts              Receive Discard Counts
    ----------------------------------   ---------------------------------
    reason                 count         reason                 count
    ---------------------- -----------   ---------------------- ----------
    M3UA conversion error  3             M3UA PDU Error         1
                                         management blocking    1
                                         lrg MSU not supported  1


    Stored Transmit Discard Data
    -----------------------------------------------
    b0 04 04 04 00 6e 01 18 51 01 00 0f 49 02 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    80 04 04 04 00 d2 01 00 23 05 05 05 02 1f 61 02
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    80 04 04 04 00 d2 01 00 13 20 19 02 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00




    Stored Receive Discard Data
    -----------------------------------------------
    01 00 04 01 00 00 00 18 00 0b 00 08 02 00 00 00
    00 06 00 08 00 00 00 04 00 00 00 00 00 00 00 00

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04   
    02 10 00 2b 00 04 04 04 00 05 05 05 0d 02 00 96

    01 00 00 10 00 00 00 1c 00 0c 00 08 00 00 00 06
    00 07 00 0c 01 00 02 02 00 00 00 18 00 00 00 00

    MSUCOUNT: command complete

;

Signaling Link Bytes Report

The IPSG signaling link bytes report is the same as the IPLIMx link bytes report.

This example shows a signaling link bytes report for an IPSG card:

pass:loc=1303:cmd="msucount -b"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report


    SLK Transmit counts                      SLK Receive counts
    ---------------------------------------  --------------------------------
           bytes/     avg    max      max    bytes/     avg    max      max
    slk    sec        msu    avg msu  msu    sec        msu    avg msu  msu
    -----  ---------  -----  -------  -----  ---------  -----  -------  -----
    A      0          0      24       24     0          0      0        0
    B      62         31     31       31     62         31     31       31
    A1     0          0      24       24     0          0      0        0
    A2     0          0      24       24     0          0      0        0
    A3     0          0      0        0      0          0      0        0
    A4     0          0      0        0      0          0      0        0

    ---------------------------------------  --------------------------------
           62         31     31       31     62         31     31       31
    ---------------------------------------  --------------------------------

This example shows the B link report:

pass:loc=1305:cmd="msucount -b a"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report

    SLK Transmit counts                      SLK Receive counts
    --------------------------------------   --------------------------------
           bytes/     avg    max      max    bytes/     avg    max      max
    slk    sec        msu    avg msu  msu    sec        msu    avg msu  msu
    -----  ---------  -----  -------  -----  ---------  -----  -------  -----
    A      0          0      24       24     0          0      0        0

    ---------------------------------------  --------------------------------
           0          0      24       24     0          0      0        0
    ---------------------------------------  --------------------------------


    MSUCOUNT: MSU Count Report

Routing Context Report

The msucount -x <routing context> report for an IPSG card displays the equivalent of the msucount -l report for all signaling links on the card that are members of the linkset containing the specified routing context.

This example shows a routing context report:

pass:loc=1303:cmd="msucount -x 74565"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0
    MSUCOUNT: MSU Count Report


    ------------------------------------------------
    Routing Context Measurements
    ------------------------------------------------

    SLK Transmit counts                  SLK Receive counts
    ----------------------------------   -----------------------------
    slk  rate   msus        bytes        rate   msus        bytes
    ---  -----  ----------  ----------   -----  ----------  ----------
    A    0      3           72           0      0           0

    ----------------------------------   -----------------------------
         0      3           72           0      0           0
    ----------------------------------   -----------------------------



    MSUCOUNT: command complete

;

IP Connection Report

The IP connection statistic report for an IPSG card contains data regarding MSUs (tx/rcv), MSU bytes (tx/rcv), and discarded data (tx/rcv) for a specific socket or an association. The -a <aname> report for M3UA links adds the Replicated M3UA PDU sent, Replicated M3UA PDU rcvd, SS7 SNM sent, Discarded rcv due to SS7 SNM not supported, and Discarded rcv due to no SS7 SNM capacity.

The existing Discarded rcv due to M3UA PDU error and Invalid rcontext counts are also supported.

This example shows an aname report:

pass:loc=1303:cmd="msucount -a a1303a"
    rlghncxa03w 08-01-29 11:31:09 EST  EAGLE 38.0.0

 
    MSUCOUNT: MSU Count Report


    ---------------------------
    IP Association Measurements
    ---------------------------


    Transmit PDUs                        Receive PDUs
    ----------------------------------   -----------------------------
    pdus            bytes                pdus             bytes
    ----------      ------------------   ----------       ----------
    3               72                   0                0


    SS7 SNM counts
    ----------------------
    sent        rcvd
    ----------  ----------
    0           0


    Receive Discard Counts
    ----------------------------------
    reason                 count
    ---------------------- -----------
    M3UA PDU error         3


    Stored Receive Discard Data
    -----------------------------------------------
    01 00 00 00 00 00 00 1c 00 0c 00 08 00 00 00 06
    00 07 00 0c 01 00 02 02 00 00 00 18 00 00 00 00

    01 00 00 00 00 00 00 1c 00 0c 00 08 00 00 00 06
    00 07 00 0c 01 00 02 02 00 00 00 18 00 00 00 00

    01 00 00 00 00 00 00 1c 00 0c 00 08 00 00 00 06
    00 07 00 0c 01 00 02 02 00 00 00 18 00 00 00 00




    MSUCOUNT: command complete
;
pass:loc=1304:cmd="msucount -a a1304m3ua1"
Command Accepted - Processing

    rlghncxa03w 08-01-29 11:31:09 EST EAGLE 38.0.0

    MSUCOUNT: MSU Count Report


    ---------------------------
    IP Association Measurements
    ---------------------------


    Transmit PDUs                        Receive PDUs
    ----------------------------------   -----------------------------
    pdus            bytes                pdus             bytes
    ----------      ------------------   ----------       ----------
    58              3380                 5                292


    SS7 SNM counts
    ----------------------
    sent        rcvd
    ----------  ----------
    8           7


    Receive Discard Counts
    ----------------------------------
    reason                 count
    ---------------------- -----------
    SS7 SNM not supported  1 
    SS7 SNM no capacity    1 
    M3UA PDU error         13
    invalid rcontext       5


    Stored Receive Discard Data
    -----------------------------------------------
    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 01
    02 10 00 2b 00 04 04 04 00 05 05 05 05 00 00 9a

    01 00 03 01 00 00 00 08 00 00 00 00 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04
    02 10 00 2b 00 04 04 04 00 05 05 05 85 02 00 9a

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04
    02 10 00 2b 00 04 04 04 00 05 05 05 85 02 00 9a

    01 00 04 01 00 00 00 18 00 0b 00 08 02 00 00 00
    00 06 00 08 00 00 00 04 00 00 00 00 00 00 00 00

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04
    02 10 00 2b 00 04 04 04 00 05 05 05 85 02 00 9a

    01 00 01 01 00 00 00 3c 00 06 00 08 00 00 00 04
    02 10 00 2b 00 04 04 04 00 05 05 05 85 02 00 9a

    01 00 01 01 00 00 0a fc 00 06 00 08 00 00 00 0a
    02 10 0a eb 00 04 32 01 00 04 32 01 0d 02 00 99

    01 00 01 01 00 00 00 08 00 00 00 00 00 00 00 00
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

    01 00 07 01 00 00 00 70 00 06 00 08 00 00 00 02
    01 15 00 08 00 00 00 80 01 02 00 18 00 02 00 03




    MSUCOUNT: command complete

;

Output Specific to High-Speed Link (HSL) cards (SS7HC and ATMHC - non-IP7 GPLs)

Note:

The -a, -x, -k, -p, and -t options are not supported for HSL cards.

Note:

The option to display a full help report is not supported for HSL cards.
pass:loc=1103:cmd="msucount -h"
    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0

    Usage: msucount  [[-l [link]] | [-f]|
                     [-r] [-h]]
 
    Options:  -l display signaling link report
              -f display full report
              -r resets the specified counts
              -h display command help
              -l link r resets the counts for specified link


    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT command complete

Link Reports

The link report contains the statistics of the equipped links (TDM/ATM) on the SS7HC/ATMHC cards collected on a per link basis.

An SS7HC/ATMHC generic link report is reported if the MSUCOUNT command is entered without any parameters. The output contains data regarding MSU bytes (tx/rcv), %bandwidth used (tx/rcv), MSUs (tx/rcv) collected during the last full second per link. Total MSU counts (tx/rcv) per link since the card load time or the last reset are also displayed.

pass:loc=1301:cmd="msucount"
    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: Command In Progress

;
    MSUCOUNT: MSU Count Report


    SLK     Last Transmit Counts/Total MSUs    Last Receive Counts/Total MSUs
    ---     ---------------------------------  --------------------------------
    slk     bytes   %bw      msus total msus   bytes   %bw     msus  total msus
    ---     ------- ----    ----  ----------   ------- ----    ----  ----------
    A         51200  20%     700  1234567890     26700  10%     400  1234567890
    B        256000 100%    5000  1234567890    256000 100%    5000  1234567890
    ---     ------- ----    ----  ----------   ------- ----    ----  ----------
    TOTAL    307200         5700  2469135780    282700         5400  2469135780

    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: command complete

;

The full link report includes the generic information, the maximum amount seen for each MSU, and the percent bandwidth tracked for the full one second period since the card load time or the last reset.

pass:loc=1301:comd="msucount -f"
    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: Command In Progress

;
    MSUCOUNT: MSU Count Report


    SLK   Last Second/MAX Transmit Counts    Last Second/MAX Receive Counts
    ---   ---------------------------------- ----------------------------------
    slk   bytes   %bw  %max  msus       mmax bytes   %bw  %max  msus       mmax
    ---   ------- ---- ----  ----       ---- ------- ---- ----  ----       ----
    A       51200  20%  40%   700       1385   26700  10%  20%   400        730
    B      256000 100% 100%  5000       5000  256000 100% 100%  5000       5000
    ---   ------- ---- ----  ----       ---- ------- ---- ----  ----       ----
    TOTAL  307200            5700             282700            5400


    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: command complete

;

If the -l slk option is specified, then the statistics for the specified link is shown (if the link is equipped).

On cards running SS7HC GPL, in addition to the information shown in the Generic and Full reports, data is collected for the error counts (MSUs and SUs) and retransmits pegged during the last full second. Averages for the MSUs, percent bandwidth, bytes transmitted and received for the last rolling sampling period, and the maximum of these averages since the card was loaded or the data was reset is also displayed.

pass:loc=1301:cmd="msucount -l a"
    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: Command In Progress

;
    MSUCOUNT: MSU Count Report


                     Last       Avg        Avg Max    Max        Total
                     --------   --------   --------   --------   ----------
     TX Bandwidth:        98%        61%        80%        98%
     RX Bandwidth:        98%        61%        80%        98%
     Bytes TXed:         7840       4900       6370       7840   1248056004
     Bytes RXed:         7840       4900       6370       7840   1024579036
     MSUs TXed:           160        100        130        160     45937854
     MSUs RXed:           160        100        130        160     41495837
     Errored SUs:           1                               10          103
     Errored MSUs:          4                                4           21
     Retransmits:          10                               23          353
     Forced PCR:           20                               50          189


    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: command complete

;

On cards running ATMHC GPL, the -l slk option, in addition to the information shown in the Generic and Full reports, data is collected for the different types of error counts during the last full second. Averages for the MSUs, percent bandwidth used, bytes transmitted and received for the last rolling sampling period and the maximum of these averages since the card was loaded or the data was reset is displayed. The total number of MSUs and bytes and errors since the card was loaded or the data was reset is also displayed.

pass:loc=1301:cmd="msucount -l a"
    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: Command In Progress

;
    MSUCOUNT: MSU Count Report


                     Last       Avg        Avg Max    Max        Total
                     --------   --------   --------   --------   ----------
     TX Bandwidth:        98%        61%        80%        98%
     RX Bandwidth:        98%        61%        80%        98%
     Bytes TXed:         7840       4900       6370       7840   1248056004
     Bytes RXed:         7840       4900       6370       7840   1024579036
     MSUs TXed:           160        100        130        160     45937854
     MSUs RXed:           160        100        130        160     41495837
     Errored SUs:           1                               10          103
     Errored MSUs:          4                                4           21
     Retransmits:          10                               23          353
     Forced PCR:           20                               50          189


    tekelecstp 10-01-19 11:50:34 EST  EAGLE 41.1.0
    MSUCOUNT: command complete

;