Use this command to configure data used by the upgrade software during an upgrade of an in-service EAGLE from a source release to the target release.

Parameters

addtblcnv (optional)

This parameter sets the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.

Caution:

The addtblcnv parameter should be used only under the direction of My Oracle Support (MOS).

Range:

0 - 1023

assignset (optional)

Assigned Set. The card specified by the loc parameter is assigned to the upgrade-grouping set specified by this parameter.

Range:

0

removes the card from the set list

2 - 10

assigns the card to that particular set list for the group corresponding to the card type

deltblcnv (optional)

This parameter clears the flag of the corresponding entry in the Table Conversion Definition table that forces the table to be converted during a software upgrade.

Caution:

The deltblcnv parameter should be used only under the direction of My Oracle Support (MOS).

Range:

0 - 1023

limsets (optional)

LIM Sets. This parameter sets the number of sets for link cards.

Range:

2 - 10

loc (optional)

Location. The location of a network card to be assigned to a set specified by the assignset parameter.

Range:

1101 - 1113, 1115, 1201 - 1218, 1301 - 1318, 2101 - 2118, 2201 - 2218, 2301 - 2318, 3101 - 3118, 3201 - 3218, 3301 - 3318, 4101 - 4118, 4201 - 4218, 4301 - 4318, 5101 - 5118, 5201 - 5218, 5301 - 5318, 6101 - 6118

src (optional)

Source. The disk that physically contains the upgrade target release.

Range:

fixed

The upgrade target release is on the fixed disk

remove

The upgrade target release is on the removable drive

srvsets (optional)

Service Sets. This parameter sets the number of sets for service cards.

Range:

2 - 10

threstype (optional)

Threshold type. The type of thresholding to be used during the upgrade.

Range:

set

Network conversion is based on the defined sets of cards

Example

chg-upgrade-config:addtblcnv=327

chg-upgrade-config:deltblcnv=327

chg-upgrade-config:sak=vbjyapdpbtejb:src=fixed

chg-upgrade-config:threstype=set:srvsets=2:limsets=4

Dependencies

The addtblcnv and deltblcnv parameters cannot be specified together in the command.

4904 E4904 Cmd Rej: ADDTBLCNV and DELTBLCNV cannot be specified together.

One of the optional parameters must be specified in the command.

2136 E2136 Cmd Rej: At least one optional parameter is required

The srvsets and limsets parameters cannot be specified unless the threstype is being changed to or has been changed to set.

5482 E5482 Cmd Rej: SRVSETS or LIMSETS not valid unless threstype = SET

The loc parameter is required when the assignset parameter is specified.

5483 E5483 Cmd Rej: LOC must be specified with ASSIGNSET

The value specified for the assignset parameter cannot be greater than the current value of srvsets or limsets for the specified card.

5484 E5484 Cmd Rej: ASSIGNSET value out of range for card group

The chg-upgrade-config command cannot be issued when SFAPP(P)->OAM sync is ON.

3637 E3637 Cmd Rej: Turn OFF SFAPP(P)->OAM sync before this command

This command cannot be entered when CAT2 IPSM to OAM syncing is in progress.

3652 E3652 Cmd Rej: IPSM to OAM SYNC in progress

Output

chg-upgrade-config:addtblcnv=327

    rlghncxa03w  07-03-13  08:15:45 EST  EAGLE 37.5.0
    Command Completed. 
;