Corporate Info  |  News  |  Solutions  |  Products  |  Partners  |  Services  |  Events  |  Download  |  How To Buy
	http://www.oracle.com/technology/documentation/index.html   |   Site Map   |   Search   |   PDF Files   |   Contact   |   Glossary
Tuxedo Doc Home   |   Messages   |   Catalog List   |   Previous   |   Next

CMDTUX Messages 4500-4599

4500	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed while allocating a message in the TMS.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4501	ERROR: Tuxedo typed buffer routine failed
	Description	An attempt to create a message in the TMS failed for a reason other than allocating memory.
	Action	Review other messages earlier in the log that indicate what caused the failure.
4503	WARN: BBL failed to wake up the blocking process - val. TPERRNO - val
	Description	The BBL found a blocking process and tried to format a message to wake up the process. The message generation failed and the process will not be awaken immediately.
	Action	Check the log for other related messages. It may be a memory allocation failure.
4504	ERROR: Memory allocation error receiving reply from TAGENT on lmid
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed while receiving a message in the tlisten process. The message was received from lmid.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4505	ERROR: Memory allocation failure
4506	ERROR: Tuxedo typed buffer routine failed
4507	WARN: FACTORYROUTING val (for INTERFACE interfacename) is not defined in the ROUTING section
	Description	The entry in the INTERFACES section for interfacename has a ROUTING parameter that does not match the name of an entry in the the ROUTING section with a TYPE parameter of FACTORY.
	Action	Correct the configuration and re-load.
	See Also	ubbconfig(5)
4511	ERROR: Duplicate *INTERFACES section
	Description	There are multiple INTERFACES sections defined in the UBBCONFIG file.
	Action	Remove the extraneous INTERFACES section from the UBBCONFIG file.
	See Also	ubbconfig(5)
4512	ERROR: *GROUPS section must appear before *INTERFACES section
	Description	The INTERFACES section was put before the GROUPS section in the UBBCONFIG file. There must be a GROUPS section before the INTERFACES section.
	Action	Correct the UBBCONFIG file to specify the GROUPS section before the INTERFACES section.
	See Also	ubbconfig(5)
4513	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed in tmloadcf while processing the *INTERFACES section.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4514	ERROR: Could not initialize sort of *INTERFACES section
	Description	An internal error occurred while attempting to sort the INTERFACES section during tmloadcf.
	Action	Attempt to load the configuration again via tmloadcf. If the error occurs again, please contact your BEA Customer Support.
	See Also	ubbconfig(5), tmloadcf(1)
4515	ERROR: Could not turnaround sort of *INTERFACES section
	Description	An internal error occurred while attempting to sort the INTERFACES section of the configuration file during tmloadcf.
	Action	Attempt to load the configuration again via tmloadcf. If the error occurs again, please contact your BEA Customer Support.
	See Also	ubbconfig(5), tmloadcf(1)
4516	ERROR: Couldn't retrieve data from *INTERFACES sort
	Description	An internal error occurred while attempting to sort the INTERFACES section of the configuration file during tmloadcf.
	Action	Attempt to load the configuration again via tmloadcf. If the error occurs again, please contact your BEA Customer Support.
	See Also	ubbconfig(5), tmloadcf(1)
4518	ERROR: Interface id must be <= val characters in length
	Description	The INTERFACE name indicated by the arrow is invalid because it is more than 15 characters in length.
	Action	Specify an interface name value that is less than or equal to 15 characters in length.
	See Also	ubbconfig(5)
4519	ERROR: Need different SRVGRP for the INTERFACE val.
	Description	The same interface has been specified more than once, but the SRVGRP parameter is absent.
	Action	Edit the UBBCONFIG file and specify different SRVGRP entries for each INTERFACE defined.
	See Also	ubbconfig(5)
4520	ERROR: INTERFACE val can't have SRVGRP val on different entry.
	Description	The same interface has been specified more than once, using the same SRVGRP value.
	Action	Edit the UBBCONFIG file and specify different SRVGRP entries for each INTERFACE defined.
	See Also	ubbconfig(5)
4522	ERROR: Interfaces val can't have two different ROUTING values
	Description	The indicated interface name has two different routing criteria associated with it.
	Action	Edit the configuration file such that if multiple ROUTING entries exist for the same interface name but have different SRVGRP parameters, the ROUTING parameter must be the same for all of these entries.
	See Also	ubbconfig(5)
4523	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed in tmloadcf while processing the *INTERFACES section.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4524	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed in tmloadcf while processing the *INTERFACES section.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4525	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed in tmloadcf while processing the *INTERFACES section.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4526	ERROR: Memory allocation failure
	Description	An attempt dynamically to allocate memory from the operating system using malloc() failed in tmloadcf while processing the *INTERFACES section.
	Action	Make sure the operating system parameters are set correctly for the amount of memory on the machine and the amount of memory that can be used by a process. Reduce the memory usage on the machine or increase the amount of physical memory and/or swap space on the machine.
4527	ERROR: AUTOTRAN specified for INTERFACE interface_name SRVGRP groupname with no TMS.
	Description	An entry for interface interface_name with group name groupname in the INTERFACES section of the UBBCONFIG file has the AUTOTRAN parameter set to Y but the group is not associated with a resource manager (that is, TMSNAME is not set).
	Action	Either set the AUTOTRAN parameter to N or associate the interface with a group that has a resource manager.
	See Also	ubbconfig(5)
4528	WARN: AUTOTRAN specified for INTERFACE interface_name with TRANTIME=0.
	Description	An entry for interface interface_name in the INTERFACES section of the UBBCONFIG file has the AUTOTRAN parameter set to Y but an unlimited transaction timeout value. This can be dangerous because the automatically started transactions will not timeout in the event of failures.
	Action	It is recommended that a transaction timeout value be specified.
	See Also	ubbconfig(5)
4529	ERROR: Failure during input to sort of *INTERFACES section
	Description	The tmloadcf command sorts the entries in the INTERFACES section by interface name. During this processing, an internal error occurred. Since sort processing uses temporary memory and disk space, the most common cause of sort failure is if these resources run out. The temporary files used for sorting are usually placed in /usr/tmp or /tmp.
	Action	Check that there is available temporary disk space in /usr/tmp and /tmp. Try running the command again when the system is less heavily loaded.
	See Also	tmloadcf(1), ubbconfig(5)
4531	ERROR: LOAD parameter must be >= 1 and <= 32767
	Description	The LOAD parameter in the INTERFACES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 1 and 32,767, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4533	ERROR: PRIO parameter must be >= 1 and <= 100
	Description	The PRIO parameter in the INTERFACES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 1 and 100, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4535	ERROR: FACTORYROUTING factoryrouting_name must be <= val characters
	Description	The factoryrouting_name of the INTERFACES section of the configuration file must be <= 15 characters.
	Action	Specify a value that is less than or equal to 15 characters.
	See Also	tmloadcf(1), ubbconfig(5)
4537	ERROR: TRANTIME parameter must be >= 0 and < 2147483648
	Description	The TRANTIME parameter in the INTERFACES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 0 and 2,147,483,647, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4539	ERROR: The SRVGRP parameter must be <= val characters
	Description	The SRVGRP parameter in the configuration file must be a string of 30 or fewer characters.
	Action	Choose a SRVGRP value that is no more than 30 characters and make sure it matches a group name in the GROUPS section.
	See Also	tmloadcf(1), ubbconfig(5)
4541	ERROR: Group name val must match a name from the *GROUPS section
	Description	The SRVGRP parameter of the INTERFACES section in the configuration file does not match an entry in the GROUPS section. This can be due to a direct error here, or a previous error while compiling the group name entry.
	Action	Correct the SRVGRP entry, or the group name entry that it is supposed to match.
	See Also	tmloadcf(1), ubbconfig(5)
4543	ERROR: TIMEOUT parameter must not be < 0
	Description	The TIMEOUT parameter in the INTERFACES section of the ubbconfig(5) file was specified as a negative value.
	Action	Change the parameter value in the ubbconfig(5) file and rerun tmloadcf(1).
	See Also	BEA TUXEDO Administrator's Guide, tmloadcf(1), ubbconfig(5)
4544	ERROR: BUFTYPE parameter not allowed for FACTORY ROUTING
	Description	A BUFTYPE parameter was specified for a ROUTING entry of TYPE FACTORY.
	Action	Change the entry type or remove the BUFTYPE parameter.
	See Also	ubbconfig(5)
4545	ERROR: Duplicate *ROUTING entry val for FACTORYROUTING
	Description	More than one entry in the ROUTING section has the same entry name and a TYPE of FACTORY.
	Action	Remove the duplicate entry in the ROUTING section.
	See Also	ubbconfig(5)
4546	ERROR: MAXINTERFACES parameter must be >= 0 and < 32767
	Description	The MAXINTERFACES parameter in the RESOURCES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 0 and 32766, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4547	ERROR: MAXOBJECTS parameter must be >= 0 and < 32768
	Description	The MAXOBJECTS parameter in the RESOURCES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 0 and 32767, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4548	ERROR: MAXOBJECTS parameter must be >= 0 and < 32768
	Description	The MAXOBJECTS parameter in the RESOURCES section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 0 and 32767, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)
4550	ERROR: FIELDTYPE parameter required for FACTORY ROUTING val
	Description	A entry in the ROUTING section had type FACTORY but did not have a FIELDTYPE parameter.
	Action	Either change the TYPE or add a FIELDTYPE parameter.
	See Also	ubbconfig(5)
4551	ERROR: *ROUTING entry val FIELDTYPE does not match datatype of RANGES
	Description	A entry in the ROUTING section had a FIELDTYPE parameter for type short, long, float, or double, but a RANGES parameter with string values.
	Action	Correct the FIELDTYPE parameter or RANGES parameter so that the type matches the values.
	See Also	ubbconfig(5)
4552	ERROR: *ROUTING entry val FIELDTYPE does not match datatype of RANGES
	Description	A entry in the ROUTING section had a FIELDTYPE parameter for type string or character, but a RANGES parameter with numeric values.
	Action	Correct the FIELDTYPE parameter or RANGES parameter so that the type matches the values.
	See Also	ubbconfig(5)
4553	ERROR: You do not have a valid M3 SDK license
	Description	buildserver(1) was running without having a valid BEA M3 system SDK license (e.g., only an RTK license was installed).
	Action	Buy a BEA TUXEDO system SDK license.
4560	ERROR: Unable to determine license level
	Description	buildserver was run but the command was unable to read the TUXEDO license to determine if transactions are enabled.
	Action	Install a valid TUXEDO license file in $TUXDIR/udataobj before running the command.
4561	ERROR: No license for Transactions
	Description	buildserver was run but the command read the TUXEDO license and found that transactions were not enabled.
	Action	Install a valid TUXEDO license file, that allows for transaction support, in $TUXDIR/udataobj before running the command.
4588	ERROR: Could not add field val to fielded buffer, Ferror32=error
	Description	The Event Broker was unable to add a field fieldname (e.g., TA_SUBSCRIPTION, TA_BLOB_TYPE, TA_BLOB_VALUE) to the event message. The FML32 error is printed as error. The event message will not be processed.
	Action	See the log for other related errors. The log should also indicate the status of the message.
4589	ERROR: Could not delete field val from fielded buffer, Ferror32=val
	Description	The Event Broker was unable to delete a field fieldname (e.g., TA_SUBSCRIPTION, TA_BLOB_TYPE, TA_BLOB_VALUE) from the event message. The FML32 error is printed as error. Processing continues unaffected.
	Action	No action is necessary. See the log for other related errors.
4590	ERROR: Cannot open file val for reading
	Description	The event server couldn't open file file for reading the subscription database.
	Action	The event server reads a new copy of the subscription database from the temporary file file. This message indicates that the server couldn't open the temporary file for reading. Check the file system parameters and take corrective action.
4592	ERROR: TMSCOUNT parameter must be > 1 and <= 256
	Description	The TMSCOUNT parameter in the GROUPS section of the configuration file must be within the proper range of values.
	Action	Specify a value that is between 2 and 256, inclusive.
	See Also	tmloadcf(1), ubbconfig(5)